valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
Repeat the above operation to reenter the code. 50 RQT5333 * О HOME THEATER TV VCR OO TUNER/ ► TAPE CO BAND ooo O CD O TOP MENU ,—. DVD o O o ENTER OCÜD DISPLAY ,-s MENU O O CD STEREO SURBOUND SP DELAY LEVEL - OO OOOO ÔÔÔH ÔÔÔ V CH A TWVIDE( OCDO MUTING - VOL + ООО How to change the remote control code TV VCR О о I 2 3 Hold down the button corresponding to the component you wish to operate. Continue to hold the button down and... Aim the remote control at the component you wish to operate and carefully and slowly press the numbered buttons to enter the appropriate two-digit code number. (Refer to the table below for the code number.) When the two-digit code number is entered, the remote control will automatically output the on/off signal. If the remote control has been correctly changed to the code for the component to be operated, the component will be switched ON or OFF. 17ПЯ If there is more than one code number indicated in the code table, repeat the above procedure until you find a code number for which the power of the component is switched ON or OFF. ET Center speaker Surround speaker (left) a POWER 6/1 A SPEAKERS B !/_/_/ I I /1 II I _//_ / / / !//_"/ A SPEAKERSB l_ I / I tt / r a ‘SIZE” © A SPEAKERS B /_ /_// //I / / / /1 / //1/ / SFC MODE (O) I Reference for speakers The speaker indicators □ This part of the display indicates which speakers sound comes from. The corresponding indicators will not light if you selected "NONE" during the speaker setting procedure, or if you turned the subwoofer off. The surround and center speaker indicators do not light when STEREO mode is selected page 40). Front, center, and surround channel settings KD The following settings may be necessary if you replace the speakers included with this unit. They should be performed in this case to get the most from this unit's reproduction modes (^ page 40,42). Set the SIZE, DISTANCE, and FILTER for your speakers. In SIZE Set the type (LARGE or SMALL) and presence of your speakers. Select “LARGE” if the speakers can produce bass (below around 100 Hz). Select “SMALL” if the speakers cannot produce bass. If you aren’t using center or surround speakers select “NONE” so the sound is produced through the front speakers. In DISTANCE Enter the distance of each speaker from the listening position so the sound from the speakers reaches the listening position at the same time. The unit calculates the delay time for the center and surround speakers based on these distances. In FILTER Enter the cutoff frequency for your subwoofer based on the bass capability of your front speakers. The factory setting is 100 Hz. U Press [POWER] on the receiver. B Press [A] and [B] at the same time. "SETTING” appears on the display. B Press [A] to select what you want to set. Each time the button is pressed the display switches as follows, DISTANCE -* FILTER-► DR COMP SIZE □ When “SIZE" is selected 0 Press [B] to select the speaker channel to be set. Each time the buttons is pressed the display switches as follows. FRONT--CENTER-* SURROUND t_I (D Turn [SFC MODE] to set the type (LARGE, SMALL) of the speaker. Each time the selector is turned the display switches as follows. Front: LARGE SMALL Center, Surround: LARGE SMALL NONE The factory settings are as follows. Front speakers: LARGE Center and surround speakers: SMALL (D Repeat steps © and (2) to complete the size settings for the front, center and surround speakers. 51 RQT5333 Reference j Preparatory steps El When “DISTANCE" is selected 0 Press [B] to select the speaker channel to be set. Each time the selector is turned the display switches as follows. FRONT-►CENTER-► SURROUND t_I ©Turn [SFC MODE] to set the distance. Distance can be set at 1 foot intervals between 3 feet to 20 teet. The factory settings are as follows. Front and center speakers; to FEET Surround speakers: 5 FEET (f) Repeat steps (D and (D to complete the distance settings for the front, center and surround speakers. Turn [SFC MODE] to set the cut off frequency. Each time the buttons is pressed the display switches as follows. 100^: 150^:200 (Hz) Press [A] and [B] at the same time. “COMPLETE" appears on the display. If you allow about 10 seconds to elapse between setting, the procedure is cancelled, all settings are returned to how they were, and the previous display is restored. Begin again if this occurs. For your reference: The settings remain as they are until changed by the above procedure, even after the power has been turned off. For front speakers with an impedance under 8 ft ID Press and hold (A] or [B] until “LOW IMP" lights up on the display. If even one of the speakers being used has an impedance under 8 ft, press and hotd down either [A] or [B] for 4 seconds or more to set the impedance on the main unit to low. (Press and hotd down once again for 4 seconds or more to turn it off.) Note that when “LOW IMP...