valutazioni - , GPA:
(
)
)
Produttore : Samsung
File Size : 861.24 kb
File Nome :
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Use an optical cable to connect digital audio equipment. (DAT deck, MD recorder, etc.). Remove the dust cap (1) from the CD DIGITAL OUT jack. Then, connect an optical cable plug to the CD DIGITAL OUT jack. (1) When the CD DIGITAL OUT jack is not being used Attach the supplied dust cap. The loudspeaker connector terminals are located on the rear of the system. There are four terminals on the system: Two for the left speaker (marked L) Two for the right speaker (marked R) To achieve the correct sound quality, connect the: Red wire to the + terminals Black wire to the – terminals 1 To connect a wire to a terminal, push the tab as far as it will go: To the right on the system 2 Insert the wire, up to the plastic sheathing, in the hole. 3 Push the tab back: To the left on the system, until it clicks into place To the top on the loudspeaker Result: The wire is pinched and held firmly in place. 4 Repeat the operation for each wire. (Right Speaker) (Left Speaker) R L AUX IN R L SPEAKER (6.) (+) R L SPEAKER (6.) DIGITAL OUT (OPTICAL) FM (75.) AM ANT. (–) (+) (–) Directions in Installing Speaker Installation in a place near heating apparatus, under direct lay of light or with high humidity may cause performance degradation of the speaker. Do not install on the wall or on a high place of pole or other unstable place to prevent any safety accident caused by falling of the speaker. Do not take the speaker apart from TV or computer monitor. The speaker near the TV or computer monitor may influence the quality of the screen display. 8 GB 9 The AM aerial (for long and medium waves) can be: Placed on a stable surface Fixed to the wall (you must first remove the base) The AM aerial connector terminals are located on the rear of the system and are marked AM . To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires. Always keep them at least 2 inches (5 cm) away. Connecting the AM (MW)/LW Aerial How to connect a COAXIAL TYPE aerial. Connect a 75. antenna to the FM antenna terminal. Plug the connector on the FM aerial supplied into the coaxial socket (75.) marked FM on the rear of the system. Follow the instructions given on Page 14 to tune into a radio station, and determine the best position for the aerial. If reception is poor, you may need to install an outdoor aerial. To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75. coaxial cable (not supplied). Connecting the FM Aerial DIGITAL OUT (OPTICAL) FM (75.) AM ANT. R L AUX IN R L SPEAKER (6.) AM ANT. DIGITAL OUT (OPTICAL) FM (75.) AM ANT. R L AUX IN R L SPEAKER (6.) DIGITAL OUT (OPTICAL) FM (75.) AM ANT. R L AUX IN R L SPEAKER (6.) Setting the Clock Viewing the Various Functions on Your System Viewing the Various Functions on Your System GB You can view the various functions available on your system. Press the Demo button. Result: The various functions available are listed in turn on the display. All these functions are described in detail in this booklet. For instructions on how to use them, refer to the appropriate sections. To cancel this function, press Demo again.2 1 On/Standby Demo Timer /Clock Mono/ST Preset/ Memory PTY RDS Display Your system is equipped with a clock which allows you to turn your system on and off automatically. You should set the clock: When you first purchase the mini-compact system After a power failure After unplugging the unit For each step, you have a few seconds to set the required options. If you exceed this time, you must start again. 1 Switch the system on by pressing On/Standby. 2 Press Timer/Clock twice. Result: CLOCK is displayed. 3 Press Enter. Result: The hour flashes. 4 To... Turn the Multi Jog knob to the... Increase the hours Right Decrease the hours Left When the correct hour is displayed, press Enter. 5 Result: The minutes flash. 6 To... Turn the Multi Jog knob to the... Increase the minutes Right Decrease the minutes Left When the correct time is displayed, press Enter. 7 Result: The clock starts and is displayed, even when the system is in standby mode. You can display the time, even when you are using another function, by pressing Timer/Clock once. You can also use Program/Set button on the remote control to instead Enter button in step 3, 5, 7. You can also use / buttons to instead Multi Jog knob in step 4, 6. Volume + _ On/Standby Multi Function Multi Jog Demo Timer /Clock Mono/ST REC/Pause Down Normal Dubbing HI - Speed CD Synchro Program Shuffle Enter CD Repeat Preset/ Memory Deck 1/2 REV.Mode CD AUX TAPE TUNER Band D / P / S DIRECT PLAY & SELECTION CD–R/RW PLAYBACK Up Tuning Mode PTY RDS Display 2 1 3,5,7 4,6 10 Listening to a Compact DiscLoading and Changing Compact Discs GB The CD disc changer can contain up to three 12 cm or 8 cm compact discs without using an adapter. Never force the compact disc carrousel when opening and closing the compartment. Never press down or place objects on the carrousel. Always treat your compact discs with ca...
Questo manuale è adatto anche per i modelli :Stereo - MAX-L65 (861.24 kb)