valutazioni - 4, GPA: 3.3
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
2 Insert two AAA, LR03 or equivalent batteries, taking care to respect the polarities: + on the battery against + in the battery compartment – on the battery against – in the battery compartment The main lead must be plugged into an appropriate socket. Before plugging your system into a main socket, you must check the voltage. Plug the main lead into an appropriate socket. Press the ( ) button to switch your micro component system on. Connecting your System to the Power Supply 2 Replace the cover by sliding it back until it clicks into position.3 1 7 The auxiliary input can be used to take advantage of the sound quality of your micro component system when listening to other sources. Examples: A television A video disc player A Hi-Fi stereo video cassette recorder To connect to the external source, the source must have an audio output. In addition, you need an RCA connection cable. Set the system to standby mode and disconnect it and the external source from the main socket. Connect the audio cable to the rear of the micro component system. Connect the... To the connector marked... Red jack R (right) White jack L (left) For optimum sound quality, do not invert the right and left channels. Plug the system back into the main socket and press the ( ) button to switch it on. Select the AUX source by pressing the AUX button. Result: AUX is displayed. Switch the external source on. Example: You can watch a film and take advantage of stereo sound provided that the original sound track is in stereo (as if you were in a cinema). 1 2 3 4 5 Directions in Installing Speaker Installation in a place near heating apparatus, under direct lay of light or with high humidity may cause performance degradation of the speaker. Do not install on the wall or on a high place of pole or other unstable place to prevent any safety accident caused by falling of the speaker. Do not take the speaker apart from TV or computer monitor. The speaker near the TV or computer monitor may influence the quality of the screen display. Main Speaker Connection: Connect the Speaker cords (red/black) to the Main Speaker jacks of System. Connecting MAIN Speaker: Use the MAIN speaker connection cable (Red/White) to connect the MAIN speaker. Red wire to the R terminals White wire to the L terminals Connecting Subwoofer Speaker: Use the subwoofer speaker connection cable (Black/Violet) to connect the SUBWOOFER speaker. This unit can output CD digital sound signals through this jack. Use an optical cable to connect digital audio equipment. (DAT deck, MD recorder, etc.). Remove the dust cap (1) from the CD DIGITAL OUT jack. Then, connect an optical cable plug to the CD DIGITAL OUT jack. When the CD DIGITAL OUT jack is not being used. Attach the supplied dust cap. CD Digital Out Jack (1) 8 GB Connecting to an External Source Speaker Connection MAIN 110v~ 127v 220v~ 240v (Right Speaker) (Left Speaker) The AM aerial (for long and medium waves) can be: Placed on a stable surface Fixed to the wall (you must first remove the base) The AM aerial connector terminals are located on the rear of the system and are marked AM ANT. To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires. Aays keep them at least 2 inches (5 cm) away. How to connect a COAXIAL TYPE aerial. Connect a 75. antenna to the FM antenna terminal. Plug the connector on the FM aerial supplied into the coaxial socket (75.) marked FM on the rear of the system. Follow the instructions given on Page 15 to tune into a radio station, and determine the best position for the aerial. If reception is poor, you may need to install an outdoor aerial. To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75. coaxial cable (not supplied). Connecting the FM Aerial MAIN MAIN 9 GB Connecting the AM (MW) Aerial MAIN DEMO Function Setting the Clock GB Y on the surrounding lighting conditions. 4,6 1 2 3,5,7 4,6 You can view the various functions available on your system. 1 Press the DEMO/DIMMER button. Result: The various functions available are listed in turn on the display. All these functions are described in detail in this booklet. For instructions on how to use them, refer to the appropriate sections. 2 To cancel this function, press the DEMO/DIMMER button again. DIMMER Function Your system is equipped with a clock which allows you to turn your system on and off automatically. You should set the clock: When you first purchase the micro component system After a power failure After unplugging the unit For each step, you have a few seconds to set the required options. If you exceed this time, you must start again. 1 Switch the system on by pressing ( ) . Press the TIMER/CLOCK button twice. 2 Result: CLOCK is displayed. 3 Press the PROGRAM/SET button. Result: The hour flashes. 4 To... Press... Increase the hours Decrease the hours 5 When the correct hour is displayed, press the PROGRAM/SET button. Result: The minutes flash. 6 To... Press... I...