valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Units are designed for operation as follows. Europe and U.K. ........................................................... AC 230 V only U.S.A. and Canada ...................................................... AC 120 V only China and Russia ........................................................ AC 220 V only Australia ....................................................................... AC 240 V only *Other countries .................... AC 110-120 / 220-240 V switchable For the United Kingdom Preparation section Factory fitted moulded mains plug 1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse. 2. The fuse cover must be refitted when replacing the fuse in the moulded plug. 3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. IMPORTANT : The wires in the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live Do not connect those leads to the earth terminal of a three- pin plug. AC 110 - 120V ‘ AC 220 - 240V ‘ *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC voltage selector switch Move switch lever to match your line volt- age with a small screwdriver or other pointed tool. Note: Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selec- tor switch. The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit. CLASS 1 LASER PRODUCT The marking of products using lasers (Except for some areas) Safety precautions WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI- ANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SER- VICING TO QUALIFIED SERVICE PERSONNEL. RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNI- TUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVIC- ING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. CAUTION 3Caution : Read this page carefully to ensure safe operation. Before applying power 3Caution : Read this page carefully to ensure safe operation. Before applying power Contents Preparation section Before applying power............................... 2 Safety precautions........................................................... 2 Special features................................................................ 5 Accessories....................................................................... 5 System connection........................................... 6 Connection of the system accessories.......................... 6 Connection of other accessories (Commercially available parts)...................................... 8 Controls and indicators................................... 9 Display................................................................................ 9 Main unit........................................................................... 10 Operation of remote control unit................. 12 Basic section Basic use method........................................... 14 Playback of CD................................................ 16 Playback of tape..............................................18 Receiving broadcast station.........................20 Collective presetting of stations (auto preset).......... 22 Channel space setting................................................... 22 Recording on tape.......................................... 24 Application section Various CD playback features...................... 26 Listening in the desired sequence (program playback)................................................... 26 Repeated playback......................................................... 27 Listening to an unexpected title sequence (random playback)..............................