valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
h DISPLAY • Show current status. i MUTE • Mute or restore volume. j PROG • Program tracks. • Program radio stations. k REPEAT • Play a track or all tracks repeatedly. l SOURCE • Select a source: disc, FM, or AUX. abcdefghijkl 3 Connect Connect speakers Note ••Insert the stripped portion of each speaker wire into the socket completely. ••For optimal sound, use the supplied speakers only. ••Connect only speakers with impedance that is the same or higher than the supplied speakers. Refer to the Specifications section of this manual. 1 For one speaker, insert the red wire to the red (R+) socket on the back of the main unit, and the black wire into the black (R-) socket. 2 For another speaker, repeat step 1 to insert the wires into the red (L+) and the black (L-) socket. To insert each speaker wire: 1 Hold down the socket flap. 2 Insert the speaker wire fully. 3 Release the socket flap. Connect power Caution ••Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back or the underside of the Micro Hi-Fi system. ••Before connecting the AC power cord, make sure that you have completed all other connections. Connect the AC power cable to the power outlet. 4 Get started Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the rear of the apparatus. Write the numbers here: Model No. _____________________________ Serial No. ______________________________ Prepare the remote control Caution ••Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. ••Risk of decreased battery life! Never mix different brands or types of batteries. ••Risk of product damage! When the remote control is not used for long periods, remove the batteries. ••Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. For first-time use: 1 Remove the protective tab to activate the remote control battery. To replace the remote control battery: 1 Open the battery compartment. 2 Insert one CR2025 battery with correct polarity (+/-) as indicated. 3 Close the battery compartment. Turn on Press POWER. »»The unit switches to the last selected source. Switch to standby Press POWER again to switch the unit to standby mode. »»The red standby indicator turns on. »»The backlight on the display panel turns off. 123123 5 Play disc 1 Press SOURCE repeatedly to select the disc source. 2 Open the disc compartment. 3 Insert a disc with the printed side facing up. 4 Close the disc compartment. • To pause/resume play, press . • To stop play, press . Play options Skip to a track During play, press / to select another track. Search within a track 1 During play, press and hold / . 2 Release to resume normal play. Display play information During play, press DISPLAY repeatedly to select different play information. Program tracks You can program a maximum of 20 tracks. 1 In disc mode, in the stop position, press PROG to activate the program mode. »»[P-] (progra10m) is displayed. 2 Press / to select a track number, and then press PROG to confirm. 3 Repeat steps 1 to 2 to select and store more tracks to program. 4 Press to play the programmed tracks. »»During play, [P-] is displayed. • To erase the program, in the stop position, press . Repeat play 1 During play, press REPEAT repeatedly to select: • [r1]: play the current track repeatedly. • [rA]: play all tracks repeatedly. 2 To return to normal play, press REPEAT repeatedly until repeat mode is no longer displayed. 6 Adjust volume level and sound effect Adjust volume level During play, press VOL +/- to increase/decrease the volume level. Enhance bass During play, press DBB to turn on or off dynamic bass enhancement. Mute sound During play, press MUTE to mute or restore the volume. 7 Listen to radio Tune to a radio station 1 Press SOURCE repeatedly to select FM source. 2 Press and hold / for more than 2 seconds. »»The radio tunes to a station with strong reception automatically. 3 Repeat step 2 to tune to more stations. • To tune to a weak station, press / repeatedly until you find optimal reception. Program radio stations automatically Note ••You can program a maximum of 20 preset FM radio stations. In tuner mode, press and hold PROG for more than 2 seconds to activate automatic program mode. »»[AUTO] (auto) is displayed. »»All available stations are programmed in the order of waveband reception strength. »»The first programmed radio station is broadcast automatically. Program radio stations manually Note ••You can program a maximum of 20 preset radio stations. 1 Tune to a radio station. 2 Press PROG to activate program mode. »»[P-] is displayed. 3 Press PRESET +/- to allocate a number to this radio station, and then press PROG to confirm. »»The preset number and the frequency of the preset station are displayed. 4 Repeat the above steps to progr...