valutazioni - 3, GPA: 3.7
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Should this occur, the system will not operate properly. Remove the CD and leave the system turned on for about an hour until the moisture evaporates. • When you move the system, take out any discs. If you have any questions or problems concerning your stereo system, please consult your nearest Sony dealer. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents such as benzene, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. • Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Cleaning the cabinet Use a soft cloth slightly moistened with mild detergent solution. To save a tape permanently To prevent a tape from being accidentally recorded over, break off the cassette tab from side A or B as illustrated. If you later want to reuse the tape for recording, cover the broken tab with adhesive tape. When you are using a TYPE II (CrO2) or TYPE IV (metal) cassette, be careful not to cover the detector slots which allow the tape player to automatically detect the type of tape. Detector slots Before placing a cassette in the tape deck Take up any slack in the tape. Otherwise the tape may get entangled in the parts of the tape deck and become damaged. When using a tape longer than 90 minutes The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding etc. frequently. The tape may get entangled in the tape deck. Cleaning the tape heads Clean the tape heads after every 10 hours of use. When the tape heads become dirty — the sound is distorted — there is a decrease in sound level — the sound drops out — the tape does not erase completely — the tape does not record Make sure to clean the tape heads before you start an important recording or after playing an old tape. Use separately sold dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette. Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that have contact with the tape every 20 to 30 hours of use with a separately sold demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette. Troubleshooting If you run into any problem using this stereo system, use the following checklist. First, check that the power cord is connected firmly and the speakers are connected correctly and firmly. Should any problem persist, consult your nearest Sony dealer. General The display starts flashing as soon as you plug in the power cord even though you haven’t turned on the system (demonstration mode). • Press DISPLAY/DEMO while the system is off. The demonstration appears automatically the first time you plug in the power cord, or if there is a power outage lasting longer than half a day. In this case, reset the following: — Clock setting (see “Step 2: Setting the time”) — Press DISPLAY/DEMO while the system is off. There is no sound. • Turn VOLUME clockwise. • The headphones are connected. • Insert only the stripped portion of the speaker cord into the SPEAKER jack. Inserting the vinyl portion of the speaker cord will interfere with the speaker connection. There is no microphone sound •Turn VOLUME or MIC LEVEL to adjust the microphone volume. • Make sure the microphone is connected to the MIC jack correctly. There is severe hum or noise. • A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. “0:00” (for European and Brazilian models) or “12:00AM” (for other models) flashes in the display. • A power interruption occurred. Reset the clock and timer settings. The timer does not function. •Set the clock correctly. DAILY 1, DAILY 2, and REC do not appear when you press t/CLOCK SET. •Set the timer correctly. •Set the clock. The remote does not function. •There is an obstacle between the remote and the unit. •The remote is not pointing in the direction of the system’s sensor. •The batteries have run down. Replace the batteries. There is acoustic feedback. •Decrease the volume level. •Move the microphone away form the speakers or change the direction of the microphone. The color irregularity on a TV screen persists. •Turn off the TV set once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the speakers farther away from the TV set. The sound from the connected source is distorted. •If “VIDEO” appears in the display when you press FUNCTION, switch the display to “MD” (see the note in the “Connecting an MD deck for analog recording” section on page 9). Speakers Sound comes from only one channel or the left and right volumes are unbalanced. •Check the speaker connections and placement. There is no sound from the surround speakers (LBT-D790/XB33/XB33K/XB50/ XB60 only). •Press SURROUND to turn on the surround effect. CD Player The CD tray does not rotate. •A CD is not placed properly. A CD will ...
Questo manuale è adatto anche per i modelli :Stereo - LBT-D390 (835.59 kb)
Stereo - LBT-D790 (835.59 kb)
Stereo - LBT-G5500 (835.59 kb)
Stereo - LBT-XB33 (835.59 kb)