valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
2 Press REC TIMER. “ON” appears, and the hour indication flashes. 3 Turn OPERATION DIAL to set the hour, then press ENTER. The minute indication flashes. Use the procedure above to set the minutes. 4 Use the same procedure as in step 3 to set the time to stop recording. The display shows the timer settings. 5 Connect a transferable USB device to the B port on the unit. 6 Press "/1 to turn off the system. To activate or check the timer again Unit: Press REC TIMER, turn OPERATION DIAL until “REC SELECT” appears, and then press ENTER. RM-AMU053: Press CLOCK/TIMER SELECT, press ./> repeatedly until “PLAY SELECT” or “REC SELECT” appears, and then press ENTER. RM-AMU054: Press TIMER MENU to select “TIMER SELECT”, then press . Press v/V repeatedly until “PLAY SELECT” or “REC SELECT” appears, and then press . To cancel the timer Repeat the same procedure as above until “TIMER OFF” appears, and then press ENTER (RM-AMU053 or on the unit) or (RM-AMU054). To change the setting Start over from step 1. 38GB Tips • The system turns on before the preset time. If the system is turned on at the preset time or if “STANDBY” flashes in the display, the Play Timer and the Recording Timer will not play or transfer. • The Play Timer setting remains as long as the setting is not canceled manually. • The volume is reduced to minimum during the Recording Timer. • The Recording Timer is canceled automatically after the Recording Timer has been activated. • The Play Timer may not be activated depending on the status of the connected iPod. • Be sure that the iPod is not playing when using the Play Timer. Additional Information Additional Information Should you encounter a problem with your system, do the following: 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the problem persists, contact your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained. When the "/1 indicator flashes Immediately unplug the power cord, and check the following items. • If your system has a voltage selector, is the voltage selector set to the correct voltage? • Are you using only the supplied speakers? • Are the + and – speaker cords shortcircuited? • Is anything blocking the ventilation holes of the unit? After checking the above items and fixing any problems, plug in the power cord again and turn on the system. If the STANDBY indicator still flashes, or if the cause of the problem cannot be found even after checking all the above items, consult your nearest Sony dealer. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system. • Press DISPLAY once while the system is turned off. The demonstration disappears. The clock or timer setting is canceled. • The power cord is disconnected or a power failure occurred. Redo “Setting the clock” (page 16). If you have set the timer, redo “Using the timer” (page 36). “– –:– –” appears in the display. • The clock is not set. Set the clock (page 16). • A power failure has occurred. Set the clock (page 16) and timer settings (page 36) again. There is no sound. • Turn MASTER VOLUME clockwise (or press VOLUME + repeatedly on the remote). • The headphones are connected to the PHONES jack. • Check the speaker connections (page 15). • There is no audio output during Recording Timer. There is no sound from the subwoofer. • Check that the subwoofer is connected securely and correctly to the unit. There is no microphone sound. • Turn MASTER VOLUME clockwise (or press VOLUME + repeatedly on the remote) or turn MIC LEVEL clockwise to adjust the microphone volume. • Make sure the microphone is connected to the MIC jack correctly. Additional Continued l 39GB Sound comes from one channel, or the left and right volumes are unbalanced. Sound comes from one channel, or the left and right volumes are unbalanced. Place the speakers as symmetrically as possible. • Connect only the supplied speakers. There is severe hum or noise. • A TV or VCR is placed too close to the unit. Move the unit away from the TV or VCR. • Move the unit away from the source of noise. • Connect the unit to a different wall outlet. • Install a noise filter (commercially available) to the power cord. • Turn off surrounding electrical equipment. The timer does not function. • Check the timer setting and set the correct time (page 36). • Cancel the Sleep Timer function (page 36). • You cannot select the Play Timer and the Recording Timer at the same time. The remote does not function. • Remove the obstacles between the remote and the unit. • Move the remote closer to the unit. • Point the remote at the unit’s sensor. • Replace the batteries (R6/size AA). • Move the unit away from the fluorescent light. There is acoustic feedback. • Reduce the volume. • Move the microphone away from the speakers or change the direction of the micro...
Questo manuale è adatto anche per i modelli :Stereo - MHC-GTZ4I (1.89 mb)
Stereo - MHC-GTZ3I (1.89 mb)