valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Notes on batteries • Make sure the battery poles (plus/minus) are properly oriented. • Do not use a new battery with an old one. • Do not use different types of batteries together. • If you do not use the remote for a long period of time, remove the batteries to prevent possible damage from battery leakage and corrosion. • Do not use a battery that is leaking. • If a battery has leaked, clean the battery compartment and replace all the batteries. • Do not place the remote in an extremely hot or humid place. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. Step 2: Setting the time Before you can use the system’s timer functions, set the internal clock. The clock uses a 24-hour system on the European model, and a 12-hour system on other models. The 24-hour system is used here for illustration purposes. 2,4 1 3,5 1 Press TIMER SET. The hour indication flashes. 000 2 Press l/Lrepeatedly to set the hour. 1300 3 Press ENTER. The minute indication flashes. 1300 4 Press l/Lrepeatedly to set the minute. 1310 5 Press ENTER. The clock starts working. To reset the system clock You can reset the system clock when the system is on. 1 Press TIMER SET. 2 Press l/Lrepeatedly until “SET CLOCK” appears, then press ENTER. 3 Repeat step 2 to 5 in “Step 2: Setting the time”. Tip If you make a mistake, start over from step 1. Step 3: Presetting radio stations — Preset The system can store a total of 30 preset stations (20 for FM and 10 for AM). This section explains how to tune in stations and preset them. 6 431 2 57 1 Press FUNCTION repeatedly until “TUNER” appears. 2 Press TUNER/BAND to select FM or AM. 3 Press TUNING MODE repeatedly until “AUTO” appears. 4 Press j/J. The frequency changes as the system scans for a station. Scanning stops automatically when a station is tuned in. At that time, “TUNED” and “STEREO” (for stereo programs only) appear. FM1005 AUTO STEREO TUNED MHz 5 Press MEMORY. A preset number flashes. Getting Started1FM1005 STEREO TUNED MHz PRESET 6 Press l/Lrepeatedly to select the preset number that you want. 3FM1005 STEREO TUNED MHz PRESET 7 Press ENTER. The station is stored to the selected preset number. 8 Repeat steps 2 through 7 to preset other stations. To tune in a weak station In step 3, press TUNING MODE repeatedly until “AUTO” and “PRESET” disappear, then press j/Jrepeatedly to tune in the station. To change the preset number Start over from step 2. Tip The preset stations are saved in the system’s memory for about a day even if you disconnect the power cord or a power failure occurs. To change the AM tuning interval (not applicable on the European and Middle Eastern models) The AM tuning interval is factory-preset to 9 kHz (or 10 kHz on North American model). To switch the AM tuning interval, tune in any AM station first, then turn off the system. Pressing TUNER + on the unit down, turn the system back on. When you change the interval, all the AM preset stations are erased. To change back to the original interval, repeat the same procedure for CMT-CP2W. For CMT-CP2WA, tune in any AM station first, then turn off the system. Pressing TUNER – down, turn the system back on. Connecting optional components This section explains how to connect a variety of components to your system in order to enhance it. Refer to the instructions included with each component for details. Connecting audio components Connecting an MD deck for analog recording You can connect an MD deck to the system with commercially available audio cords. Be sure to match the color-coded pins to the appropriate jacks. To listen to the MD deck after connecting it, press MD. To the audio input jacks on the MD deck To the audio output jacks on the MD deck Connecting an MD deck for digital recording By connecting an MD deck to the system with a commercially available optical cable, you can make a digital recording from a CD. To the digital input connector on the MD deck Connecting a VCR You can connect a VCR to the system with a commercially available audio cord. Be sure to match the color-coded pins to the appropriate jacks. To listen to the VCR after connecting it, press VIDEO. To the audio output jacks on the VCR Connecting headphones Connect headphones to the PHONES jack. x.> u+ – ZmMPHONES jack Connecting external antennas You can connect an external antenna to your system to get better reception. FM antenna Connect a commercially available external FM antenna to the FM ANTENNA terminal(s) as shown below. You may also connect a TV antenna for the same purpose. Jack type A FM75W AM UANTENNA IEC standard socket connector (not supplied) Jack type B AM antenna For the AM antenna, use a 6- to 15-meter, horizontally extended insulated wire, with one end connected to the AM ANTENNA terminals as shown below. Leave the supplied AM loop antenna connected. Jack type A Getting Started FM75W AM UANTENNA Jack type BAM UFM75W UANTENNA Insulated wire (not supplied) Insulated wire (not supplie...
Questo manuale è adatto anche per i modelli :Stereo - CMT-CP2W (456.44 kb)