valutazioni - , GPA:
(
)
)
Produttore : Roland
File Size : 708.41 kb
File Nome : DSD-2_OM.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Operation with non-certified or non-verified equipment is likely to result in interference to radio and TV reception." The equipment described in this manual generates and uses radio-frequency energy. If it is not installed and used properly, that is, in strict accordance with our instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J, of Part 15, of FCC Rules. These rules are designed to provide reasonable protection against such a interference in a residential installation. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by the following measure: • Disconnect other devices and their input/output cables one at a time. If the interference stops, it is caused by either the other device or its I O cable. These devices usually require Roland designated shielded I/O cables. For Roland devices, you can obtain the proper shielded cable from your dealer. For non Roland devices, contact the manufacturer or dealer for assistance. If your equipment does cause interference to radio or television reception, you can try to correct the interference by using one or more of the following measures: • Turn the TV or radio antenna until the interferences stops. • Move the equipment to one side or the other of the TV or radio. • Move the equipment farther away from the TV or radio. • Plug the equipment into an outlet that is on a different circuit than the TV or radio. (That is, make certain the equipment and the radio or television set are on circuits controlled by different circuit breakers or fuses.) • Consider installing a rooftop television antenna with coaxial cable lead-in between the antenna and TV. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commision: "How to Identify and Resolve Radio-TV Interference Problems" This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. 9V BATTERY PEDAL (COVER) THUMB SCREW SPRING BASE COIL SPRING PEDAL GUIDE BATTERY CONNECTOR BATTERY STRAP BATTERY HOUSING SPECIFICATIONS Power ...............................9V Dry Battery x 1, AC adaptor (BOSS PSA Series) Current Draw .....................45 mA to 60mA (9VDC) Controls ............................Effect Level, Feedback Level, Time (Sampling/Delay) Others ...............................Mode Selector Switch, Pedal Switch (Normal/Effect Selector in Delay mode. Trigger Switch in Sampler mode) LED Indicator (= Battery Check Indicator) Jacks.................................Input, Output, Trigger In, AC Adaptor (PSA Series) Sampling Time...................200ms (MIN) to 800ms (MAX) Delay Time ........................50ms (MIN) to 800ms (MAX) Frequency Response ...........Sampling/Delay sound: 40Hzto7kHz(!jdB) Direct Sound: 10 Hz to 60kHz (ijdB) Residual Noise ...................Sampling/Delay mode: -95dBm (IHF-A) Normal mode: — 100dBm or less (IHF-A) Input Impedance ................1 Mil (FET input) Output Load Impedance......lOkilormore Dimensions........................70(W) x 55(H) x 125(D) mm/2%"(W) x 23/ie"(H) x 4'Vi6"(D) Weight ..............................450g/1lb * Specifications are subject to change without notice. Printed in Japan '85 Feb E-3 Ö INSTRUCTIONS FEATURES The BOSS DSD-2 is an effect unit that features both the sampler function (800ms digital recorder) and the delay function (50 to 800ms). The Trigger In Jack can be used to sync the DSD-2 with a rhythm machine, or to sample a sound and use it as an external sound source, or to obtain an echo effect that perfectly syncs to the rhythm. 43 AC & BATTERY ' POWERED DSD-2 Digital Sampler /Delay 4r output INPUT 4r TRIG.IN4» Digital Sampler /Delay DSD-2 ■ > Please read these instructions carefully for proper operating procedures for the BOSS DSD-2. NOTICE CAUTIONS • Please be sure to use the AC Adaptor BOSS PSA-120, 220 or 240 depending on the voltage system in your country. ACA-series can not be used, as the DSD-2 draws more current (45-60mA 9V DC) than usual compact effect units. ► The battery (one Dry Battery, 9V) will last for 30 minutes to 2 hours (manganese) or 5 to 10 hours (alkaline), depending on the conditions. The use of a BOSS PSA-Adaptor and alkaline battery is recommended for a longer time performance ► Avoid using this unit in extreme heat or humidity, or where it may be affected by dust. »When the unit is not in use for a long period, remove the battery to prevent problems cause...