valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
MANUAL DE INICIO RAPIDO ESPANOL ( 5 – 7 ) .. GUIDE D’UTILISATION RAPIDE FRANCAIS ( 9 – 11 ) .. MANUALE RAPIDO DI UTILIZZAZIONE ITALIANO ( 13 – 15 ) .. KURZANLEITUNG DEUTSCH ( 17 – 19 ) .. QUICKSTART GUIDE ENGLISH ( 1 – 3 ) .. MANUAL DE INICIO RAPIDO ESPANOL ( 5 – 7 ) .. GUIDE D’UTILISATION RAPIDE FRANCAIS ( 9 – 11 ) .. MANUALE RAPIDO DI UTILIZZAZIONE ITALIANO ( 13 – 15 ) .. KURZANLEITUNG DEUTSCH ( 17 – 19 ) 1 NORMAL FILTERS FLANGER AUTOPAN L R AUTOCUT FILTERED LOPASS VARI-CUT RATE RATE BOX CONTENTS .. C1 .. IEC Power Cable .. Quickstart Guide .. Safety Instructions & Warranty Information REGISTRATION Please go to to register your C1. Registering your product ensures that we can keep you up-to-date with any last-minute product developments and provide you with world-class technical support, should you run into any problems. GROUND RULES 1. Make sure all items listed in the BOX CONTENTS section are included in the box. 2. READ SAFETY & WARRANTY INFORMATION BOOKLET BEFORE USING THE PRODUCT. 3. Study the connection diagram in this guide. 4. Place mixer in an appropriate position for operation. 5. Make sure all devices are turned off and all faders and gain knobs are set to “zero.” 6. Connect all stereo input sources as indicated in the diagram. 7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources. 8. Plug all devices into AC power. 9. Switch everything on in the following order: • Audio input sources (i.e. turntables, CD players, etc.) • Mixer • Last, any amplifiers or output devices 10. When turning off, always reverse this operation by turning off: • Amplifiers • Mixer • Last, any input devices CONNECTION DIAGRAM CD BURNER TURNTABLE TURNTABLE HOUSE AMP HEADPHONES CD PLAYER CD PLAYER CD PLAYER REMOTE MIXER MICROPHONE REAR PANEL FEATURES 33434367215589 1. MIC INPUT – Connect a .” microphone to this input. Microphone controls are located on the top panel. 2. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, be sure to connect the grounding wire to these terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded. Note: Some turntables have the grounding wire built into the RCA connection and, therefore, nothing needs to be connected to the grounding terminal. 3. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs. 4. AUX | PHONO INPUTS (RCA) – Connect your audio sources to these inputs. These inputs can accept both line and phono-level signals. 5. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the PHONO INPUTS. If using phono-level turntables, set this switch to “PHONO” to provide the additional amplification needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set this switch to “LINE.” 6. RECORD OUTPUT (RCA) – Use standard RCA cables to connect this Record output to a recording device, such as a CD recorder or tape deck. The level of this output is based upon pre-master levels. 7. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this Master output to a speaker or amplifier system. The level of this output is controlled by the MASTER FADER on the top panel. 8. POWER IN – Use the included power cable to connect the mixer to a power outlet. While the power is switched off, plug the power supply into the mixer first, then plug the power supply into a power outlet. 9. VOLTAGE SELECTOR – This 2-position switch sets the AC input voltage for the speaker. U.S. users should set this switch to “100-120V” whereas U.K. and most European users will need to set this to “220-240V.” 2 TOP PANEL FEATURES 1235435435476891413121110 1. MIC GAIN – Adjusts the audio level of the microphone signal. 2. MIC TREBLE & BASS – Adjusts the treble (high) and bass (low) frequencies of the audio for both mic inputs. Tip: If you experience feedback when using a microphone at loud levels, try turning down the high (treble) frequencies. 3. CHANNEL FADER – Adjusts the audio level of the corresponding channel. 4. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the rear panel. 5. CUE – Sends the pre-fader audio Cue channel for monitoring. 6. CROSSFADER – Blends audio playing between Channels 2 and 3. Sliding this to the left plays Channel 2 and sliding to the right plays Channel 3. Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer only. 7. MASTER FADER – Adjusts the output volume of the Program mix. 8. STEREO / MONO – Adjusts the Program mix for stereo or mono operation. 9. STEREO LEVEL INDICATOR – Monitors the audio level of the Program mix. 10. GRAPHIC EQUALIZER (EQ) – Adjusts the high, mid-range, and low fre...