Log:
valutazioni - 6, GPA: 4.2 ( )

Istruzioni per l'uso Peavey, Modello Duel 212

Produttore : Peavey
File Size : 1.21 mb
File Nome : 667d32a0-2e53-477a-83b2-84f6c3d63610.pdf
Lingua di insegnamento: enesfrde
Vai a scaricare



Facilità d'uso


NOTE: The ground switch is not functional on 220/240 volt models. FUSE (3) A 5 amp fuse is located within the cap of the fuse holder. Tt must be replaced with the same type and value in order to avoid damage to the equipment and to prevent voiding the warranty. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair. WARNING: The fuse should only be replaced when the power cord has been disconnected from its power source. REMOTE FOOTSWITCH JACK (4) Provided for the connection of the supplied remote footswitch. Footswitch is used to select the channel from clean to lead and to select the effect, reverb, and tremolo on or off. LEVEL (5) Adjusts the voltage level of the effects loop. If the send level is too low for a particular effects device, turn the control clockwise; if too high, counterclockwise. EFFECTS SEND (6) Output for supplying signals to external effects or signal processing equipment. 5 L SWITCH LOGIC EFFECTS RETURN (7) Input for returning signals from external low-level effects or signal processing equipment. NOTE: Signals are supplied to outboard effects or signal processing units by patching from the effects send jack (6) output into the outboard unit(s) and back into the effects return (7) input using shielded cable with l/4” phone plugs. Only non-gain effects devices (chorus, reverb, delay, etc.) should be used in the effects loop. Remote (on/off) selection of outboard effects devices can be achieved using the footswitch. PREAMP OUT (8) The preamp out jack can be used to route the amplified signal to a mixing console, tape recorder, etc. Connect the preamp output using a shielded cable to an input of the tape recorder, mixer, etc. This patch does not affect the operation of the amplifier. IMPEDANCE SELECTOR SWITCH (9) Use to select the appropriate impedance of the speaker enclosure(s). If two enclosures of equal impedance are used, the switch should be set at one-half of that value (e.g., two 16 ohm enclosures: set switch to 8 ohms; two 8 ohm enclosures: set switch to 4 ohms). When using only the internal speakers, the Impedance Selector Switch should be set to 16 ohm. SPEAKER OUTPUTS (10) Paralleled l/4” output jacks for connecting speaker enclosure(s) to the amplifier (minimum 4 ohms). When using more than one enclosure, be sure to calculate the total impedance and set the impedance switch (9) accordingly. (See section on Impedance Switch.) IMPORTANT: Use only high quality, unshielded cable for speaker connections. SPECIFICATIONS THIS BLOCK DIAGRAM PRE POST SHOWS SIGNAL FLOW WITHIN THE UNIT. IN L PUSH INPUTS f BOOST HIGH PREAMP ORDER TO THOROUGHLY GAIN /T LOW UNDERSTAND THE UNIT’S GAIN RESONANCE PRESENCE FUNCTIONS, PLEASE STUDY THE BLOCK DIAGRAM CAREFULLY. PUSH LEAD EQ CLEAN EQ LO MID HI I 1 I”‘““” MASTER LEVEL PREAMP OUT P 6 POWER AMPLIFIER SECTION The following specs are measured @ 1 kHz with presence and resonance at 0 and effects level at 10. Rated Power & Load: 120 W RMS into 16, 8, or 4 ohms Power @ Clipping: Typically @ 5% THD, 1 kHz, 120 V AC line 120 W RMS into 16, 8, or 4 ohms Frequency Response: +O, -3 dB, 50 Hz to 20 kHz @ 100 W RMS into 8 ohms Hum & Noise: Greater than 85 dB below rated power Power Amp EQ: Active presence: +10 dB @ 2 kHz Active resonance: +lO dB @ cabinet resonant frequency Power Consumption: (Domestic) 400 watts, 50/60 Hz, 120 V AC PREAMP SECTION The following specs are measured @ 1 kHz with the controls preset as follows: Low & High EQ @ 10 MidEQ @ 0 Bright Out Boost Out Shift Out Lead Posts @ 10 Presence & Resonance @ 0 Master Level @ 10 Effects Level @ 10 Reverb @ 0 Tremolo/Speed & Intensity @ 0 Nominal levels with pre gains @ 5 Minimum levels with pre gains @ 10 Preamp High Gain Input: Impedance: Very high Z, 470 kilo-ohms Lead Channel: (Channel Select In) Nominal Input Level: -38 V dBV, 12 mV RMS Minimum Input Level: -67 dBV, .44 mV RMS Clean Channel: (Channel Select Out) Nominal Input Level: -17 dBV, 40 mV RMS Minimum Input Level: -42 dBV, 8 mV RMS Maximum Input Level: 0 dBV, 1 .O V RMS Preamp Low Gain Input: (-6 dB Pad) Impedance: High Z, 44 kilo-ohms All levels are increased by +6 dB Effects Send: Load Impedance: 47 kilo-ohms or greater Output Level: -10 dBV +10 dBV, 300 mV 3 V RMS Effects Return: Impedance Very high Z, 470 kilo-ohms Input Level: -10 dBV + 10 dBV, 300 mV 3 V RMS Preamp Output: Load Impedance: 47 kilo-ohms or greater Nominal Output: +lO dBV, 3 V RMS Remote Footswitch: Special 4 button unit with LED indicators, Channel Select, Effects Loop Bypass, Reverb & Tremolo Bypass System Hum & Noise @ Nominal Level: (Clean Channel) 20 Hz to 20 kHz unweighted Greater than 75 dB below rated power Equalization: Custom Low, Mid & High passive type EQ Push Bright +6 dB @ 2 kHz Push Boost increases Gain in midrange Push Shift (Lead Channel Only) shifts frequency of mid TONE SETTINGS In Metal In In In out out out In In Country In In out out out Tone settings are general and will vary according to type of guitar, ty...

Questo manuale è adatto anche per i modelli :
Strumenti Musicali - Duel 212 (1.21 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie