valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
This will certainly score some valuable points with your soundman. To get the most out of your new DeltaBass, we suggest that you read this entire manual. Pay special attention to any warnings/cautions to ensure your safety and the safety of your product. Thank you for buying Peavey! FEATURES: • Buffered tuner send jack • Post EQ effects loop • Transformer-balanced XLR jack • Pre/Post EQ send switch for XLR jack • Ground lift switch for XLR jack • Patented DDT™ power amp compression with defeat switch and LED indicator • 160 Watts (4 ohm) power amp REAR PANEL: REAR PANEL FEATURES (1) REMOVABLE AC POWER CORD This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used. (See voltage marking on unit.) Never remove or cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord. When lost or damaged, replace this cord with one of the proper ratings. ENGLISH 1 3 2 4 3 NOTE: FOR UK ONLY As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored green and yellow must be connected to the terminal which is marked by the letter E, or by the earth symbol, or colored green or green and yellow. (2) The wire which is colored blue must be connected to the terminal which is marked with the letter N, or the color black. (3) The wire which is colored brown must be connected to the terminal which is marked with the letter L or the color red. (2) POWER SWITCH Used to turn AC mains power on or off. Place the switch in the (I) position to turn the unit on. Return it to the (O) position to turn the unit off. The Status/Power LED (22 ) on the front of the unit will illuminate to indicate the unit is on. (3) FUSE The fuse is located within the cap of the fuseholder. If the fuse should fail, IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the unit repeatedly blows fuses, it should be taken to a qualified service center for repair. WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE. CAUTION: USING A FUSE LARGER THAN THE RECOMMENDED SIZE COULD RESULT IN PERMANENT DAMAGE TO THE AMPLIFIER. (4) SPEAKER JACKS Two paralleled 1/4" speaker jacks are provided for connection to speaker enclosures. The minimum speaker load impedance is 4 ohms. FRONT PANEL: FRONT PANEL FEATURES (5) INPUT JACK This mono 1/4" input will accept signals from all types of bass pickups. (6) INPUT PAD SWITCH This switch is provided for instruments that have an extremely high output, which can result in overdriving (distorting) the input stage. Depressing the switch to its “in” position reduces the level of the input signal by 10 dB. 7 5 6 9 10 11 12 13 14 15 8 16 17 18 19 20 21 22 4 (7) TUNER SEND JACK This 1/4" jack is provided for connecting an instrument tuner to your amp. Its signal is buffered off the input jack so it is just like plugging directly into the tuner. (8) BRIGHT SWITCH This switch provides a preset boost to treble frequencies. To activate, depress the switch to its “in” position. (9) PRE GAIN CONTROL This knob controls the input gain of the preamplifier. The input gain is at its maximum when this control is turned fully clockwise. Adjusting this control will adjust the sensitivity of your amp to your playing style. (10) CONTOUR CONTROL This knob provides a specially voiced EQ as the knob is rotated clockwise. When the knob is fully counterclockwise (set to 0) there is no voicing added. (11) LOW CONTROL (11) This active tone control (shelving type, +/-15 dB) varies the low frequency boost or cut. (12) MID CONTROL This active tone control (peak/notch, +/-15 dB) adjusts the mid frequency range. (13) MID SHIFT CONTROL Use this knob to select the frequency band that the mid control cuts or boosts. (14) HIGH CONTROL This active tone control (shelving type, +/-15 dB) varies the high frequency boost or cut. (15) VOLUME CONTROL This control determines the overall volume level of the amplifier. The final level adjustment should be made after the desired sound has been achieved. Adjusting this control clockwise will increase the overall volume level. (16) LINE OUT—XLR JACK This male XLR provides a 600 ohm, transformer balanced signal for patching into a sound reinforcement or recording console. (17) PRE/POST EQ SELECT SWITCH Use this switch to select between a Pre EQ (switch set to the “out” position) or a Post EQ (switch set to the “in” position) send to the XLR line out jack. (18) GROUND LIFT SWITCH This switch is provided to lift the ground on the XLR jack when ground loops are encountered. (19) EFFECTS SEND JACK Use this mono 1/4" output for supplying signals to external low-lev...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - Deltabass Deltabass (976.28 kb)