valutazioni - 5, GPA: 3.8
(
)
)
|
Facilità d'uso
'86-E3 Products of Roland INSTRUCTIONS Please read the instructions carefully. The BOSS CS-3 is a compression sustainer that produces long sustain without distorting the original sounds. The attack volume adjusts picking forth widely and provides any drive-sound. As having the ions control function, the CS-3 allows wider variation of sound creation. Moreover, featuring the wide range of maximum input level and compression rar.ge, it can be used for any electronic musical instrument. !n addition, the CS-3 can be used as an ordfnay limiter by turning down ths sustain voiume. cs- Vh шш0 Compression Sustainer 4-wrpirr ';-fHPvr4- Cdmprasfilorv , Suetafn^r .tCS~l ■PANEL DESCRIPTION AC Adaptor Jack Love! Knob Tone Konb Output Jack Pedal Switch Compression Sustainer. CS-3 Check Indicator Sustain Knob Attack Knob Input Jack Thumb Screw Level Knob This knob changes ths volume of the effect sound. Rotating it clockwise increases tha volume and counterclockwise decreases. Therefore, this knob can be effectively used to adjust volume balance of tha effect and direct sounds. Tone Control Rotating this knob clockwise emphasises the higher frequency making sharper sounds. Counterclockwise rotation cuts tha higher frequency making softer sounds. Attack Knob This adjusts tha intensity of the attack in the picking, At its clockwise position, the attack sound is retained in each note even in fast picking, creating drive sound. Sustain Knob This knob adjusts tha sustain time. Rotating this knob clockwise increases the sustain time. By rotating It counterclockwise, the output levei is limited, therefore the CS-3 works as a limiter. Check Indicator This serves as an effect ON/OFF indicator as well as battery check. This lights up when the effect is turned on and goes out when off. Pedal Switch Push this pedal to turn the effect on (LED an}, and push it again to turn the affect off (LED off). * The FET Switching system amazingly reduces click noise, so that studio recording and live performance will now be even more successffuily achieved. AC Adaptor Jack Connect an AC adapter (BOSS ACA series! to this jack for AC operation, Input Jack This is to connect an eiectric guitar, or other electronic musical instrument. Plugging tha power cord into this jack turns the power to the CS-3 on. So please disconnect the cord when tha unit is not to be used. Output Jack Connect this jack to the external device such as amplifier. Thumb Screw Loosen this thumb screw to open the pedal cove» for battery replacement. Please do not remove tha screw from the pedal cover, or you may lose it. IMPORTANT • When operating the CS-3 from the AC line, use the BOSS AC Adaptor (ACA series!, • Avoid using the CS-3 in extreme heat, humidity or where it may be affected by dust. Ampttfter Unpiug the power cabte when the CS-3 is not to be used. OPERATION TONE ATTACK SUSTAIN After making ait the connections, sst the panel as shown Se ft. CHECK O Press the Peda! Switch. If the indicator lights up, the effect is on. and if not, the effect is off, ’ This indicator also serves as battery check, !f it becomes dimmer or does not light at all, battery replacement is required SUSTAIN Rotate the Sustain Knob to an appropriate position. * As you turn the Sustain Kncb ciockwise. you may hear noise or howling. If so, rotate it slightly countercBckwise. MM MAX MIS MAX Using the CS-3 Using the CS-3 as a Compressor as a Limiter Press the Pedal Switch to turn the effect on (LEO onl, and adjust the volume of the efiect sound using the Level Knob. Adjust the intensity of the attack with tha Attack Knob. Control the tone of the sound with the Tone Control Knob, CAUTIONS FOR REPLACING AND HANDLING BATTERY CAUTIONS AC Adaptor (Option) REPLACING BATTERY USE ONE 9-VOLT BATTERY. ©loosen the screw to open the pedal and take out the battery from the battery housing, ©Replace the battery with a new ons. ©Set the coil spring onto the spring base on the back of the pedal and shut tha pedal. Finally, insert the screw into the pedal guide ...