valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
In this manual, these names are used as appropriate ways to indicate sounds that are simulated using COSM technology. 10.GAIN Knob Adjusts distortion level. 11.VOLUME Knob Adjusts channel volume. EQUALIZER 12.BASS Knob Adjusts the tone quality of the lower range. 13.MIDDLE Knob Adjusts the tone quality of the midrange. 14.TREBLE Knob Adjusts the tone quality of the upper range. * Because COSM faithfully models the special features and characteristics of a variety of amplifiers; no sound will be produced when BASS, MIDDLE, and TREBLE knob are all set to 0 while the Type switch is set to BLACK PANEL. EFX (Effects) 15.EFX (Effects) Knob Turn this knob to chorus, flanger, phaser, or tremolo to select the corresponding effect. Turn the knob to adjust the amount of effect applied. You can also turn EFX on and off using optional footswitches (BOSS FS-5U or FS-6). * Graduations for CHORUS, FLANGER, PHASER, TREMOLO on a panel are for reference. Be sure to check the sound as you adjust the effects. Espanol Italiano Francais Deutsch EnglishPortuguesNederlands Panel descriptions CHORUS This is a spacially synthesized chorus. With spacially synthesized chorus, a method available only in stereo, the chorus effect is created by taking the sound from the right speaker (from which the effect sound is output), and the sound from the left speaker (which outputs the direct sound), and then mixing them in the actual space. This creates a greater lateral spread than that produced when the sounds are mixed electronically, providing a more natural sense of breadth. FLANGER This creates a flanging effect that creates a sort of spinning sensation with the sound. PHASER This effect adds a variable phaseshifted signal to the direct sound, giving the sound a swirling character. TREMOLO Tremolo is an effect that creates a cyclic change in volume. 16.DELAY/REVERB Knob Turn this knob to DELAY or REVERB to switch to that effect.Turn the knob to adjust the amount of effect applied. DELAY Turn the knob to change the time and amount of delay effects. REVERB Spacious-sounding stereo reverb is provided. Turn the knob to adjust the reverb level. 17. Power Indicator This indicator lights when the unit is turned on. * When operating on battery power only, the unit’s indicator will become dim during play when battery power gets too low. * Sounds may distort easily or may cut off when played at high volume as the battery power begins to fade, but this is normal and does not indicate a malfunction. In such instances, either replace the batteries or use the AC adaptor included with the unit. DELAY/REVERB 7 8 Panel descriptions 18.POWER Switch This switches the power on and off. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply: Use of Batteries” (p. 4). 19.AUX IN Jack You can connect a CD player, MP3 player or other kind of device and have it play along with your guitar or other kind of devices. This accepts a stereo miniature phone plug. * Determine the volume level by adjusting the volume control of the connected device. 20.STEREO PHONES Jack Connect headphones to this jack. * No sound is played through the unit’s speaker while the STEREO PHONES jack is in use. If you use a PCS-31 connection cable, you’ll also be able to use this as a stereo recording output. * If you're using a monaural cable, the effect might be difficult to discern. fig.01-01 21.FOOT SW (Footswitch) Jack A footswitch (BOSS FS-5U or FS-6; sold separately) connected here can be used to switch on/off MUTE and DELAY/REVERB for the MIC/LINE CH, and EFX and DELAY/REVERB for the GUITAR/INST CH. * If you use a monaural cable to connect just one footswitch, you’ll only be able to control MUTE for the MIC/LINE CH, and EFX for the GUITAR/INST CH. 22. Security Slot ( ) 23.AC Adaptor Jack Connect the included AC adopter to this jack. * Use only the AC adaptor included with the CUBE STREET. 24.Grounding terminal Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the surface feels gritty to the touch when you touch this device, microphones connected to it, or the metal portions of other objects, such as guitars. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are concerned about this, connect the ground terminal with an external ground. When the unit is grounded, a slight hum may occur, depending on the particulars of your installation. If you are unsure of the connection method, contact the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page. Unsuitable places for connection • Water pipes (may result in shock or electrocution) • Gas pipes (may result in ...