valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
These are convenient when connecting to devices that have no SUBWOOFER OUT. For detailed connection instructions, refer to "Instructions for Connecting to Devices With No SUBWOOFER OUT" (p. 9). Two types of connectors are provided: XLR connectors and 1/4" phone jacks. Use the type of connectors that match the device you are connecting. These output jacks provide +4 dBu line level output. * No sounds are output from the THRU OUT jacks when the power is turned off. * The PHASE switch, BOTTOM switch, and CROSSOVER knob do not affect the output from THRU OUT. * When inputting only to the INPUT L (MONO) jack, the signal is output from both the L and R jacks of THRU OUT. 8. GND LIFT switch Allows you to make/break the connection between the GND pins of the THRU OUT XLR connectors and the KCW-1's ground. If you encounter noise problems that are possibly caused by a ground loop, try changing the switch position to alleviate the problem. 9. POWER switch This switches the power on and off. * Before turning the power on or off, be sure to put the VOLUME knob at 0. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * Refer to p. 10 for the order in which to turn the power to connected devices on and off. * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply" (p. 5). 10. POWER indicator This lights up when the power is on. 11. AC inlet Connect the included Power cord here. Plug it firmly in, so that the cable does not accidentally become disconnected. ■ Front Panel 12. OPERATION indicator This lights up when the power is on. When a connected foot switch is used to switch off the KCW-1's speaker output, the indicator flashes. 7 Connect your KCW-1 Instructions for Connecting to Devices Equipped with SUBWOOFER OUT Connectors (Mono Connection) When connecting to devices equipped with SUBWOOFER OUT connectors, make the connections between the KCW-1 and other devices after referring to the following figure. E Polarity Switch DP-2 FS-5U Foot Switch (Momentary type) Device equipped with SUBWOOFER OUT Use a 1/4" phone audio cable to connect the SUBWOOFER OUT on the device featuring the SUBWOOFER OUT connector to the KCW-1's INPUT L (MONO). or Instructions for Connecting to Devices Equipped with SUBWOOFER OUT Connectors (Stereo Connection) When connecting the KCW-1 to the KC-550/350 or similar devices, and using a stereo link to play sounds in stereo, make the connections to the KCW-1 as shown in the following figure. IE Polarity Switch FS-5U Foot Switch (Momentary type) R ch (Master) SUBWOOFER OUT Lch(Sub) Use 1/4" phone audio cables to connect both the R (Master) and L (Sub) SUBWOOFER OUTs on the KC-550/350 or other devices to the KCW-1's INPUT L and R. 8 Connect your KCW-1 Instructions for Connecting to Devices With No SUBWOOFER OUT When connecting to devices with no SUBWOOFER OUT connectors, connect such equipment to the KCW-1 after referring to the following figure. m Polarity Switch FS-5U Foot Switch (Momentary Type) MONITOR OUT Powered Monitor Input signals from the VS Series and other output devices to the INPUT connectors. Connect DS Series powered monitors or similar devices to the KCW-1's THRU OUT. The INPUT section features XLR and 1/4" phone jacks. Although both types may be used simultaneously, adjust the connected devices to attain the proper volume balance between the input devices. THRU OUT also includes XLR connectors and 1/4" phone jacks. Both types may be used simultaneously. Notes Regarding the Connections * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Set the KCW-1's VOLUME knob to zero. * Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable. * This instrument is equipped with balanced (XLR) type jacks. Wiring diagrams for these jacks are shown below. Make connections after first checking the wiring diagrams of other equipment you intend to connect. ® SB © ®:GND (2): HOT (3) (3): COLD 9 Connect your KCW-1 Switching the Power On and Off Once the connections have been completed (p. 8), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. Make sure that all volume controls on the KCW-1 and connected devices are set to 0. 2. Turn on all the devices connected to the KCW-1's input jacks. 3. Turn on the KCW-1. 4. Switch on any equipment connected to the KCW-1's THRU OUT jacks....