valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Be sure to use a separate power outlet. Concerning placement • Placing the unit near power amplifiers or other equipment containing large transformers may induce hum. • Should the unit be operated nearby television or radio receivers, TV pictures may show signs of interference, and static might be heard on radios. In such cases, move the unit out of proximity with such devices. 0 Avoid placing the unit where it may be subject to direct sunlight, or where near devices that may emanate heat. Avoid confining it within a tightly closed car or other such places. Otherwise, the unit may become deformed or discolored. Maintenance 9 For everyday cleaning, wipe the unit with a soft dry cloth, or one that is dampened slightly. To remove dirt that is more stubborn, wipe using a mild, neutral detergent. Afterwards, make sure to wipe thoroughly with a soft cloth 0 Never apply benzene, thinner;., aicohol or any like agents, to avoid the nsk of discoloration and deformation. Other Precautions # Protect the unit from a strong impact. # Never apply strong pressure to the display, or strike it in any way. The KR-55 contains a backup battery to preserve the settings when the power is turned off. The battery life is 5 years or longer, but we recommend that you change it every 5 years. When the battery runs low, the following display will appear. Please contact a Roland service center for replacement. *The first replacement after purchase may become necessary in less than 5 years. if the following display appears, it ts possible that part or ail of the data m memory has been lost. To return all data to the factory settings, refer to the explanation on page 12 "Restoring the Factory Settings". Joint boit □ Joint nut E Knob bolt F Assembling Procedure ©Insert the Joint nuts D into the holes on the back panel A, and adjust the joint nuts O with the screwdriver provided as shown in Fig 2. ©Attach the back panel A to the side panels 8. and tighten the joint bolls C. : ®Place the keyboard on the stand, and fix with the knob bolts E. ©Loosen the cord clamp's screw F with the screwdriver provided, pul the power cord into the clamp F, and retighlen the screw.{Fig 3) J Music Stand Attach the music stand as shown in the diagram. I jrr n wrr u m i i ni u uv\v \\\ w\ ^ Before moving or tr ansporting the unit, be sure to remove the music stand Function Guide Labels These labels indicate the function of each button when setting performance functions or making MIDI settings Affix the labels as shown. Upper labe! t CD CDj CD CDj CD CD CD CDU CD CD CD CD CD CD CD CD CD EZD CD CD CD CD [fj CD CDD CD CD CD CD CD CD" Lower label P Pèdal Connections UPPER LOWER LEVEL D Wttg MAX Pedal jacks Connect one or two of the following pedals to the pedal jack(s). FS-5U • When using a pedal to adjust the volume or pan By connecting an expression pedal (EV-5, EV-10) to the pedal jack, you can control the volume or pan. EV-5 EV-10 □p-e ‘ A separately so!d cable DP-6 (PJ-1M) is required When using only one pedal, connect it to the UPPER terminal. This will allow you to simultaneously control both UPPER and LOWER with a single pedal. (-+ page 6 0) If you wish to use the pedal to control Volume, set the pedal function to "3". If you wish to use the pedal to control Pan, set the pedal function to "4". (—* page 6 ED ) * With the factory settings, both pedals are set to function as damper pedals (to make the sound decay gradually). External output _GUT1 ft © Connecting Another Electronic Musical Instrument Or Mic t Output jacks Use these jacks to connect the KR-55 to an external amp or recording device. Connect these jacks to the AUX IN jacks of an audio amp, or the INPUT jack of s guitar amp v_;.....................................................................................J Ö 4 Input jacks Input level knob Adjust the level of the INPUT jacks. When another electronic musical instrument or microphone is connected, it can be heard through the built-in speakers of ^•Turning The Power On (T) Connect the power cable and insert it into an AC outlet. Be sure to use the correct AC voltage for your unit. ON OFF Rear panel Press the button Press the button to turn the once again ro tun power ON the power Off (?) To turn the power on, press the -fiTrnK POWER button located at the The headphone jack is located at the lower left on the front of the keyboard. When headphones are connected, the built-in speakers will not sound, allowing you to practice without disturbing others. —.--i left side of the panel. * Since the KR-55 contains a protection circuit, ther? will be a short delay before operation begins In order to take advantage of the stereo capabilities of the KR-55, we recommend that you use stereo headphones (RH-12, RH-tOO, or similar sold separately) 3 oHow to adjust the VOLUME control This slider controls the volume output from the internal speaker, headphone jack, and output jacks...