valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
This indicator also serves as battery check. * If the indicator fails to light or lights but only dimly, replace the battery with a new one. e LEVEL KNOB This adjusts the level of the effect sound. Rotating this knob clockwiswe increases the amount of the effect sound, and vice versa. 0 TONE KNOB This knob controls the tone of the sound. Rotating this clockwise emphasizes the higher frequencies, creating sharper sound, and counterclockwise rotation cuts the higher frequencies, creating softer sound. o OUTPUT JACK Connect an amplifier or other effect to this jack. 0 PEDAL SWITCH This turns on or off the effect. * Adopting the FET switching system, this Pedal Switch is released from the click noise, therefore, even more successful live performance and studio recording are made possible. 0 AC ADAPTOR JACK This is to connect the AC adaptor (BOSS ACA-120, 220 or 240). * AC operation allows long and secured performance. o THRESHOLD KNOB This adjusts the threshold level. Rotating the knob clockwise raises the threshold level, lowering the.limit-ing effect. Rotating it counterclockwise lowers the level, raising the limiting effect. 0 RELEASE KNOB This adjusts the release time. Rotating the knob clockwise makes longer release time, and vice versa. o INPUT JACK To this jack, connect an electric or electronic musical instrument such as a bass guitar. * The unit is turned on when the plug is connected to the Input Jack. So, when the unit is not to be used, disconnect the connection cord from the Input Jack. ® THUMB SCREW Loosen this screw when replacing the battery. * Do not remove the screw from the Pedal. ■ IMPORTANT NOTES • Use only the BOSS AC adaptor ACA 120, 220 or 240 depending on the voltage system in your country. • Do not use this unit in extreme heat, humidity, or where it may be affected by dust. ooOOOO °o Bass Amplifier To AC Adaptor Jack BOSS AC Adaptor (ACA-120, 220 or 240) --Î L.* LJ ♦•OUTPUT INPUT 4- Limiter Lm-2 cn—■ !<*=■ •ot=m Bass Guitar Plugging in the Input Jack automatically turns the unit on. ffl Keyboard ("When the unit is not to be used, disconnect the connection cord from the Input Jack. ■ OPERATION CHECK O THRESHOLD TONE RELEASE | After making all the necessary connections, set the knobs as shown in the picture. CHECK o Press the Pedal Switch down, and make sure that the indicator O lights (effect is on). * If the indicator fails to light up or lights only dimly, replace the battery with a new one. THRESHOLD Set the threshold level with the Threshold Knob ■ ■ BATTERY REPLACEMENT USE 9V BATTERY (T) Loosen the Thumb Screw and open the Pedal. (2) Take out the battery from the Battery Housing and pull up the Battery Snap Cord. (3) Connect a new battery to the Battery Snap Cord and replace it to the Battery Housing. * Be sure that the Battery Snap Cord is securely pushed in. ® Put the Coil Spring to the Spring Base and close the Pedal. * Make sure that the Battery Snap Cord is not caught in the Pedal or Coil Spring (D Firmly tighten the screw. Pedal 9V Battery Battery Snap Thumb Screw Spring Base Coil Spring Battery Housing Battery Snap Cord ■ Set the release time with the Release Knob 0. Adjust the tone with the Tone Knob 0. Adjust the volume with the Level Knob 0. ■ PRECAUTIONS • When the unit is not to be used for a long period, remove the battery to prevent the trouble caused by the battery leakage. • If the battery voltage drops, effect becomes inferior or no sound is produced. To prevent this, replace the battery. • Be sure to keep the battery securely connected even while using the AC adaptor, and the unit will continue to operate even if the AC adaptor cord comes out during performance. • Unplug the cord from the Input Jack when the unit is not in use, to avoid wasting the battery. AC ADAPTOR Please be sure to use the BOSS ACA-120, 220 or 240 depending on the voltage system in your country. Using any other adaptor will cause malfunction or even breakdown. 4 RELEASE MIN MAX BOSS ACA-120, 220 or 240 (Optional) SETTING MEMO THRESHOLD THRESHOLD LEVEL TONE RELEASE | LEVEL TONE RELEASE | • ••••••• ooou • ••••••• MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX [^Roland® 2603077700 UPC 2603077700 ■ SPECIFICATIONS Power ......................................9VDC 006P (x 1). AC Adaptor (ACA-120, 220 or 240) Current Draw ..........................12mA(9VDC) Controls...................................Level. Tone, Release, Threshold Switch .....................................Effect On/Off Indicator ..................................Effect On/Off (=Battery Check) Jacks........................................Input, Output, AC Adaptor Residual Noise........................Less than -lOOdBm (IHF-A) (Level and Tone set to the center) Input Impedance ....................1MQ Output Load Impedance........More than 10k0 Dimensions .............................70(W) x 55(H) x 125(D) mm 2%" x T...