valutazioni - 5, GPA: 3.4
(
)
)
|
Facilità d'uso
3 Installing the MV8-OP1............................................................4 Installation de la MV8-OP1 (French language for Canadian Safety Standard) ...................................... 6 Using the MV8-OP1.................................................................. 8 Outputting analog audio from analog multi output.................. 8 Inputting audio via a digital connection (coaxial/optical) ........ 8 Transferring digital audio via R-BUS ...................................... 9 Connections and settings for R-BUS devices ...................... 12 Copyright © 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland International Web Site: About the MV8-OP1 About the MV8-OP1 . You can digitally connect a digital audio device (CD player, MD player, DAT recorder) and sample without impairing the audio quality. . You can input digital audio of a variety of sampling frequencies. * Since the MV8-OP1 contains a sampling rate converter, there is no limitation on the sampling frequencies that can be input. All signals will be converted to 44.1 kHz. . You can connect devices that have an R-BUS connector, such as the Roland VS-2480CD or XV-5080, for digital audio input/output via R-BUS (2-channel input / 8-channel output). . You can individually output the audio signals of the MV-8800 to its multi outputs. This is convenient when you are using the MV-8800 with an external mixer. (Analog output and R-BUS output are all available.) . When used with the DIF-AT24 (sold separately), an additional MIDI IN and OUT (16 channels) is added. * Don’t connect the R-BUS connector to an RMDB connector, SCSI connector, RS-232C connector, or parallel connector. Doing so will cause malfunctions. * Don’t connect or disconnect the R-BUS connector while the power is turned on. Doing so will cause malfunctions. MV-8800 Using the MV8-OP1 Panel Descriptions Panel Descriptions . The jacks shown in items 1–3 are available if the MV8-OP1 AUDIO I/O EXPANSION (separately sold) is installed. You can make output settings from the INSTRUMENTS screen (Screen Guide; p. 114) and the PARTIAL EDIT screen (Screen Guide; p. 125). DIGITAL IN Connectors These are digital audio input connectors. “A” is a coaxial type connector, and “B” is an optical type connector. R-BUS Connector This is a digital 2-channel input/8-channel output connector. You can also set the input select setting to receive audio input from R-BUS channels 1 and 2, or use the R-BUS channels 1–8 to output the audio from the MULTI OUTPUT bus. ANALOG MULTI OUTPUT Connectors These jacks output the audio from the MULTI OUTPUT bus. MV-8800 Using the MV8-OP1 Installing the MV8-OP1 Precautions for expanding option Installing the MV8-OP1 Precautions for expanding option Always turn the unit off and unplug the AC plug before attempting installation of the MV8-OP1. Install only the specified option. Remove only the specified screws. . To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the board. . Before you touch the board, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged. . When handling the board, grasp it only by its edges. Avoid touching any of the electronic components. . Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it. . Do not touch any of the printed circuit pathways. . Never use excessive force when installing a circuit board. If it doesn’t fit properly on the first attempt, remove the board and try again. . When circuit board installation is complete, double-check your work. . When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged. . When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. . Use a Philips screwdriver of the appropriate size to avoid damaging the screw heads (a number of 2 screwdriver). If an unsuitable screwdriver is used, the head of the screw may be stripped. . Turn the screwdriver counter-clockwise to loosen the screws-turn it clockwise to tighten them. tightenloosen . Be careful not to let the screws drop inside the MV-8800’s body. . Do not leave the option slot cover removed. After installation of the MV8-OP1 is complete, be sure to replace the cover. . Be careful not to cut your hand on the edge of the cover or the opening edge while removing the cover. MV-8800 Using the MV8-OP1 Installing the MV8-OP1 5 MV-8800 Using the MV8-OP1 1. Turn off the power of the MV-8800 and the connected devices, and ...