valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Rotating this clockwise deepens the effect. * With this knob rotated fully clockwise, the Manual Knob does not work at all. @ FEEDBACK This knob controls the amount of feedback signal in normal or inverted phase. At the center position, the feedback level is zero, and turning the knob clockwise will increase the feedback level of the normal phase. And rotating it counterclockwise will increase the feedback level of the inverted phase, emphasizing the flanging effect. O BALANCE This adjust the amount of the direct and effect sound. At the center position, the mixing balance is equal, making the strongest flanging effect. * When using the RBF-10 for making an effect loop with the device such as PA mixer, set the Balance Knob fully clockwise. 0 POWER INDICATOR This lights up when the unit is turned on. 0 POWER SWITCH 3 < REAR PANEL> ® ® ® f ® $ ® # INPUT JACKS Connect a musical instrument or audio equipment to this jack. * The standard phone and pin jacks do not work at a time. If both are simultaneously used, the standard phone jack will have priority. 4D LEVEL SWITCH Set this knob to an appropriate position depending on the output level of the connected device. 20dBm” position may be selected for a usual electric musical instrument (such as an electric guitar), and 10dBm" position for audio equipment. ® D+E OUTPUT JACKS Through this jack, the mixture of direct sound and effect sound of the normal phase is sent out. ® D-E OUTPUT JACKS Through this jack, the mixture of direct sound and effect sound of the inverted phase is sent out. * The standard and the pin jacks of the D + E and D —E Outputs can be used at a time. ® EFFECT REMOTE JACK Connect the footswitch FS-1 (optional) to this jack, and Effect/Normal mode can be selected without reaching out your hand. * The above function cannot be obtained if the Effect Switch on the front panel is turned off. When two RBF-10's are setup, connect the Remote Jacks of the two units, and Effect/Normal of the two units can be controlled by either of them. ® MODULATION BUS JACK When you setup two RBF-10's to obtain stereo effect, use this jack to sync the modulations of the two RBF-10's. (See "■MODULATION BUS") ® POLARITY SWITCH When two RBF-10's are set up, the polarity of either RBF can be inverted with this switch. * When the Polarity Switch is set to "INV", the Manual Switch affects invertedly, too. ® AC ADAPTOR JACKS This is to connect the AC Adaptor (BOSS PSA-120, 220 or 240). Connect the adaptor to IN. When using this unit to supply power to other BOSS Micro Rack Series, connect the supplied DC cord to OUT. * When only one AC adaptor is used for supplying power to more than one unit, please be sure that the total amount of the current draw does not exceed 200mA. (The current draw is shown on the rear panel of each unit.) ■ CONNECTIONS AC Adaptor BOSS PS A-120, 220 or 240 “»P (Optional) To other BOSS Micro Rack Series Footswitch FS-1 (Optional) USE BOSS 5SA ADAPTOR CNLY О 0 IN OUT a. INV A NOR POLARITY BUS 9V DC E05Q<- MODULATION _ -lOdBm Я - 2üdBm EFFECT REMOTE OUTPUT OUTPUT LEVEL INPUT (For Modulation Sync: To the Modulation Bus of Other RBF-10) (All the BOSS Micro Rack Series show the current draw here.) Guitar Amplifier Tape Recorder Electric Guitar дан* inminnmii Keyboard Tape Recorder ■ OPERATION 1 Set the knobs on the panel as shown below. n n u 2 Set the Level Switch to the appropriate position depending on the output level of the connected unit. * lf it is the noise that you wish to avoid more than anything, set the switch to 20dBm" position. Changing the position of the Level Switch will not affect the volume. 3 Rotate the Rate Knob to adjust the speed of the flanging effect. Q 6 4 Rotate the Manual and the Depth Knobs to adjust the depth of the effect. * When the Depth Knob is turned fully clockwise, the Manual Knob does not work at all. a w jclc»# Kt MHIM MR WW sue uw MMO O til 5 To emphasize the flanging effect, rotate the Feedback Knob. At the center position, chorus like effect is obtained. | ■MUMi EB9SS1 m KBo o limn «1 o D 6 By connecting a footswitch to the Effect Remote Jack, Normal/Effet can be changed without reaching out your hand. * Make sure that the Effect Switch on the front panel is turned on. ■ MODULATION BUS By connecting two RBF-IO's through their Modulation Buses, stereo flanging effect can be obtained. 1 Set up two RBF-10’s as shown below. AC Adaptor BOSS PSA-120, 220 or 240 Supplied DC Cord The left RBF-10 is used as a Master, and the other as a Slave. О WBH ОШЯП LfWÏÇf ou *ui um Master OUTPUT _L Pre Main Amplifier J O Tape Recoder Guitar Amplifier (< b •met MMon OUI oumn itvti Slave INPUT Electric Keyboard Tape Recoder Video Disc Player FM/TV Tuner Video Cassette Recoder ■■■——Wf » CD Play« Featuring low noise, RBF10 can also have place in AV system lor creating special sound effects. 2 Set the knobs on the fro...