valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
Thus, both the ’’Instrument Assign” Sound parameter, and ’’MIDI Channel” MIDI parameter should be set to ’’OFF”. When you wish to set the same parameter values for all Pads : If you press ALL/CENTER ] after setting a value, as in steps (5) and (6) above, ’’ALL” will appear in the display, and the value that was currently active will be set for all Pads. At this time, all Pad Indicators will light momentarily. A O [3lThe Copy Function-Convenient for Making Settings By using the Copy function, all settings in a Patch (or certain types of settings only), can be copied to another Patch. This is convenient when you wish to create a Patch that is similar to existing one. [Procedure] ® From the Play Mode, use PATCH/LEVEL j Y if A Ito select the Patch (1 - 32) which is to be the destination for the Copy. Press EDIT to select the Edit Mode. Press COPY j to select the parameters that are to be copied. With each successive press of COPY I, the display will change as shown below, allowing you to select which parameters from within a Patch will be copied. @ Using VALUE [y1 A I, select the Patch (1 - 32) you wish to copy. Press ALUENTER and the display wii! appear as shown below, indicating that the copy is being performed. C - L I ill To cancel the Copy procedure, press any button other than COPY I or ALL,/ENTER I. * Settings which have been made a pedal switch connected to the EP -1 jack are copied at the same time. (P.42) * The setting for the EP - 2 are not copied when this procedure is carried out. Press EDIT j once again to return to the Play Mode. # When wishing to copy settings made for the EP - 2 jack : If you carry out steps (D through © above when making settings for the EP - 2 jack, you can copy the Pad settings (P.42) that apply when the pedai connected to the EP - 2 jack is depressed. While in the Edit Mode, keep the pedal depressed while you press COPY |. With each successive press of COPY 1, the display wili change as shown below, allowing you to select the parameters you wish to copy. — “if fmm ”/ / _ / # /_. /_ IJ —► 9 /_ /_. IJ -► _f I C. L. U Copies only Sound parameters Copies only MIDI parameters Copies both Sound and MIDI parameters This feature allows you to select Patches in any predetermined order. To use the Patch Chain function, seiect the Patches that you intend to use in the course of a performance, and in the order you wish to use them. / / / / ■—" ^ 1 ~l 1 J -¥ J ~l /_ l_ 1 J / /_ <- 1 n 1 u 4— j -/ j /_ 1 I I 4-J The Patch Chain function allows you to link up to 32 Patches in the chain. • Setting Up a Patch Chain © Press j EDiT]to select the Edit Mode. Press PATCH CHAIN The Parameter and Pad Indicators will go out, indicating that a Patch Chain can be made. 0 1 Use VALUEfrll A 1 to select the first Patch (1 - 32), then press | ALL7ENTER If the G.B.N. method of display has been chosen for display of Patches in the Play Mode, Patch Numbers here will also be displayed using the G.B.N. method (P.15). © Repeat the selection procedure in step (3) until you have selected, in order, all the Patches you need. * If partway through the procedure you decide to cancel setting up a Patch Chain, press | PATCH CHAIN j Once this button is pressed, all settings made up to then are cancelled. (§) Press 1 ALL/ENTER | once again and the following readout will be displayed, indicating that the Patch Chain has been stored in memory. Press EDIT once again to return to the Pi ay Mode. Patch Changes Using a Patch Chain Follow the steps below to change Patches in the order they were set in the Patch Chain. © Check to make sure you are in the Play Mode. Press PATCH CHAIN{. The following will appear in the display: By pressing PATCH/LEVEL j Y1 K \, the Patches will change in the order in which they were set. When you reach the last Patch, the unit goes back to the first Patch again. * If you connect a pedal switch to the PATCH SHIFT jack on the unit's rear panel, you can then use the pedal switch to change Patches. @ Press[ PATCH CHAiN] once again, to return to the Play Mode. * While using the Patch Chain function to play, the unit cannot be put into the Edit Mode even if you press j EDIT [ Clearing the Patch Chain The following procedure erases the settings for the current Patch Chain. Once you perform this procedure, the Patch Chain will not work even if you press PATCH CHAIN while in the Play Mode. © Press EDIT to enter the Edit Mode. Press; PATCH CHAIN [and ALL/ENTER 1, in that order, and the settings for Patch Chain will be erased. Press EDIT I once again to return to the Piay Mode. __ncsivm jy 111*7 i 7 * ' ^ <«. i w«.wii wwbb»»T9w [51 Restoring the Factory Preset Patch Settings Follow the procedure below to restore the factory preset Patches you desire. * For a listing of the Factory Preset Patch settings, see P.68. (!) After turning power "OFF for a moment, hold down 1 EDIT [while you turn the power switch ”ON” again. The patch display sho...