valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
*When three seconds pass without [DISPLAY] being pressed, the setting is stored and the tuner returns to its normal mode. On: The meter lights stream to the center from the left and right. Off: The meter lights up at the left and right. Memory Function The TU-1000 retains the following settings in memory even while the power is turned off. Flat Tuning settings (number of flats) Accu-Pitch sign function setting Tuning mode setting OUTPUT jack output setting Reference pitch setting Number of meter lights setting Meter display setting - Outputting the Signal from the OUTPUT Jack Regardless of the Tuner’s On/Off Setting You can set the TU-1000 so that sounds input at the INPUT jack are always output from the OUTPUT jack, regardless of whether the tuner itself is switched on or off. 1.Turn off the power (unplug the instrument from the INPUT jack). 2.Hold down the TUNER ON/OFF switch and turn on the tuner (plug the instrument into the INPUT jack). 3.Press the TUNER ON/OFF switch to select the desired output function. *When three seconds pass without the TUNER ON/OFF switch being pressed, the setting is stored and the tuner returns to its normal operating mode. Sounds output from the OUTPUT jack: the meter light streams from right to left. Sounds not output from the OUTPUT jack: the meter lights up at the left and right. Turning Off the Meter’s Backlight and Rear Panel Light You can turn off the meter’s backlighting and rear panel light by holding down the TUNER ON/OFF switch for at least two seconds. To turn the light back on, press the TUNER ON/OFF switch again for two seconds or more. Make the moving light differently lighted *This function is only available for CENT display mode. 1.Turn off the power (unplug the instrument from the INPUT jack). 2.Hold down [PITCH] and turn on the power (plug the instrument into the INPUT jack). 3.Press [PITCH]. *When three seconds pass without [PITCH] being pressed, the setting is stored and the tuner returns to its normal mode. By every single touch of the [PITCH], number of the moving light can be changed. ..Restoring the Original Factory Settings (Factory Reset) You can reset the various settings you have saved to the TU-1000’s memory and restore the the original settings that the tuner had at the time it was shipped. 1.Turn off the power (unplug the instrument from the INPUT jack). 2.Hold down [MODE] and turn on the power (plug the instrument into the INPUT jack). The green light at the center of the meter lights up. 3.Press [MODE]. *If you let three seconds pass without pressing [MODE], or if you press any button other than [MODE], the tuner returns to its normal operating mode without the factory settings being restored. The green light at the center of the meter flashes three times, and the TU-1000 returns to its normal mode, with the original default factory settings restored. ..Storefront Demo Display 1.Turn off the power (unplug the instrument from the INPUT jack). 2.Hold down [FLAT TUNING] and turn on the power (plug the instrument into the INPUT jack). The storefront display appears. The storefront display remains until you turn the TU-1000’s power off and then on again, or until you press the TUNER ON/OFF switch. ..Panel Descriptions Front Panel 1.FLAT TUNING Button: Sets the amount the pitch is lowered in flat tunings. FLAT TUNING Indicator: Indicates the flat tuning setting. 2.MODE Button: Switches the tuning mode. MODE Indicator: Indicates the tuning mode setting. 3.TUNER ON/OFF Switch: Switches the tuner on and off. 4.TUNER ON/OFF Indicator: Lights when the tuner is on. 5.PITCH Button: Displays the reference pitch. PITCH Indicator: Lights while the reference pitch is being set. 6.DISPLAY Button: Switches the meter’s display pattern. DISPLAY Indicator: Indicates the meter’s display mode. 7.POWER Indicator: Lights when the power is on. 8.Meter: Indicates the input sound’s pitch. 9.Tuning Guide Indicator: Indicates when the proper tuning is reached. Pitch is flat Pitch is sharp Pitch is in tune 10.Note Name/String Number Indicator: Indicates the note name, string number, or reference pitch. Rear Panel 11.Security Slot () 12.INPUT Jack Connect the guitar, bass guitar, or other instrument to be tuned here. *The INPUT jack doubles as a power switch. Connecting the instrument’s plug turns on the tuner’s power, and disconnecting the plug switches the power off. Disconnect the cord from the INPUT jack when not using the TU-1000. 13.PARALLEL OUT Jack Use this when you want to split the signal from the INPUT jack and send it to a connected effects processor or guitar amp. 14.TUNER ON/OFF Jack Connect an external footswitch (FS-5U; sold separately) here. Connecting an FS-5U allows you to switch the tuner on and off away from the tuner. *Set the FS-5U’s polarity switch to the jack side. 15.OUTPUT Jack Connect an effects processor, guitar amp, or other such device here. Normally, the output is muted while the tuner is on. However, you can set the ...