valutazioni - 6, GPA: 4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Attaching the Tom Pad XP100T XP120T Clamp bolt (to be tightened as shown) Tom pad (back side) Rod parts Clamp rod Tom pad Clamp bolt To be inserted Clamp bolt B Clamp bolt C Clamp bolt A Continued on the next page (on the back side) U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation ©2009 Yamaha Corporation WT58990 910PO***.*01A0 Printed in Japan 1. Remove the wing nut and the two felt washers from the Cymbal Holder. Then turn the tilter sleeve in a counterclockwise direction and remove it. 2. Attach the stopper to the Cymbal Holder, and fix at a position where the L-shaped part of the stopper is on the opposite side from you. To fix the position of the stopper, use the tuning key and tighten the key bolt firmly. 3. Attach the tilter sleeve removed in step 1 to the Cymbal Holder again, and tighten it in a clockwise direction. 4. Attach one of the felt washers removed in step 1 to the Cymbal Holder. The other felt washer will not be used within the standard assembly described in this manual. 5. Insert the end of the L-shaped part of the stopper into the oval-shaped hole (shown as a) on the Cymbal Pad to set the Pad on the Holder. * Cymbal Pad PCY135 is very similar to Real High- Hat Pad RHH135. Check the model name on the reverse side. 6. Attach the included round-shaped felt with a large hole-diameter to the Cymbal Holder, then attach the wing nut removed in step 1 and tighten it. Turn the wing nut until you are certain that the Cymbal Pad is attached. The Cymbal Pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Attaching the Cymbal Pad PCY135 PCY155 PCY135 Cymbal holder Wing nut Felt washer Tilter sleeve Tuning key Key bolt Stopper Felt washer Tilter sleeve Felt washer supplied with the Cymbal Pad a Wing nut 1. Attach the included module stand to the back side of the Drum Trigger Module by using the module stand fastening screws. 2. Attach the module stand onto the holder clamp, then tighten the knob to fix the position. Attaching the Drum Trigger Module Drum Trigger Module Module stand fastening screw Drum Trigger Module (back side) Module stand Front side of the module Holder Clamp Drum Trigger Module + module stand Knob 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to prevent scratching the surface. 2. Loosen the wing bolt (shown with a) of the Hi-Hat Stand. 3. Spread out the legs of the tripod part until it stands stable. Tighten the wing bolt loosened in step 2. 4. Insert the radius rod into the hole of the frame as shown below. 5. As shown at right, loosen the wing bolt (shown with b) to remove the hi-hat clutch. * The hi-hat clutch is not used within the standard assembly described in this manual. Use the hi-hat clutch included in the RHH135. 6. Pull out the hi-hat shaft . from the upper pipe A. 7. Insert the hi-hat shaft . removed in step 6 into the nut of the lower pipe C. 8. Insert the upper pipe A into the hi-hat shaft . from above, then tighten the wing bolt (shown with c at right) at the position where the cymbal support plate is positioned at the middle area of the hi-hat shaft .. 9. Remove the felt washer and the cymbal support plate attached above the support plate, since they are not used within the standard assembly described in this manual. 10. Set the Real Hi-Hat Pad RHH135. * Refer to “Setting Up” in the RHH135 Owner’s Manual. Assembling the Hi-Hat Stand Radius rod Radius rod Wing bolt a B B C A A B A Hi-Hat clutch Cymbal support plate Support plate Cymbal support plate c b Felt washer Locate the Hi-Hat Stand, Kick Pad and Snare Stand as desired, referring to “Unit Standard Assembly” on the front page. Before assembling the unit, lay a drum mat (sold separately) on the floor. If a drum mat is not available, lay the cardboard of the included package under the Hi-Hat Stand and Kick Pad to prevent damaging the floor. Connecting the pads to the Drum Trigger Module Connect the cables plugged into the Output jacks of the Pads to the Input jacks of the Drum Trigger module. Connect the AC power adaptor to the Drum Trigger Module. The assembly is now completed. * For information about the next steps such as tuning the power on/off and checking the actual sound, refer to “Setting Up” in the Owner’s Manual of the Drum Trigger Module. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to prevent scratching the surface. 2. Attach the foot pedal (sold separately) to the Kick Pad KP125W, then fix the position so that the beater will hit the center of the Pad. * Refer to the Owner’s Manual of the KP125W. Assembling the Kick Pad Pad KP125W (Kick Pad) Beater Foot pedal (sold separately) 1. Spread out the legs of the tripod part then locate the Snare Stand on the floor. 2. Spread out the basket part of the Snare Stand, set the Snare Pad XP120SD on the basket part, then use the adjustment knob to fix the Snare Pad. Assembling the Snare Stand and Snare...