valutazioni - 1, GPA: 5
(
)
)
|
Foto e specifiche Yamaha A-S300 |
Facilità d'uso
3 Rotate the INPUT selector on the front panel (or press one of the INPUT selector buttons on the remote control) to select the input source you want to listen to. The indicator for the selected input source lights up. 4 Rotate the SPEAKERS selector on the front panel to select SPEAKERS A, B or A+B. Notes • Set the SPEAKERS selector to the A+B position when two sets of speakers are connected using bi-wire connections, or when using two sets of speakers simultaneously (A and B). • If you do not want sound to be heard from the speakers while listening with headphones, set the SPEAKERS selector to OFF. 5 Play the selected input source. 6 Rotate the VOLUME control on the front panel (or press VOLUME +/– buttons on the remote control) to adjust the sound output level. y You can adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls, or the PURE DIRECT switch on the front panel. 7 When finished listening, press A switch on the front panel outward to turn off this unit. y If Abutton on the remote control is pressed while the A switch on the front panel is in the on position, this unit enters standby mode. Press A button again to turn this unit on. Adjusting the tonal quality TREBLE LOUDNESS VOLUME BASS BALANCE PURE DIRECT ¦ Using the PURE DIRECT switch Routes input signals from your audio sources. As a result, the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals to produce more direct and high-grade sound from all input sources. Note The BASS, TREBLE, BALANCE and LOUDNESS controls do not function while the PURE DIRECT switch is turned on. 8 En PLAYING AND RECORDING ¦ Adjusting the BASS and TREBLE controls The BASS and TREBLE controls adjust high and low frequency response. The center position produces a flat response. BASS When you feel there is not enough bass (low frequency sound), rotate clockwise to boost. When you feel there is too much bass, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 Hz) TREBLE When you feel there is not enough treble (high frequency sound), rotate clockwise to boost. When you feel there is too much treble, rotate counterclockwise to suppress. Control range: –10 dB to +10 dB (20 kHz) ¦ Adjusting the BALANCE control The BALANCE control adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions. ¦ Adjusting the LOUDNESS control Retain a full tonal range at any volume level, thus compensating for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. CAUTION If the PURE DIRECT switch is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears or the speakers from being damaged, be sure to press PURE DIRECT switch AFTER lowering the sound output level or AFTER checking that the LOUDNESS control is properly set. 1 Set the LOUDNESS control to the FLAT position. 2 Rotate the VOLUME control on the front panel (or press VOLUME +/– buttons on the remote control) to set the sound output level to the loudest listening level that you would listen to. 3 Rotate the LOUDNESS control until the desired volume is obtained. y After setting the LOUDNESS control, enjoy listening to music at your preferred volume level. If the effect of the LOUDNESS control setting is too strong or weak, readjust the LOUDNESS control. Recording a source Notes • For the A-S500, audio signals are not output via the LINE 2 REC or LINE 3 REC output jacks when LINE 2 or LINE 3 is selected with the REC OUT selector. • For the A-S300, audio signals are not output via the LINE 2 REC or LINE 3 REC output jacks when LINE 2 or LINE 3 is selected with the INPUT selector. • This unit must be turned on in order to record. • The VOLUME, BASS, TREBLE, BALANCE and LOUDNESS controls and the PURE DIRECT switch have no effect on the source being recorded. • Check the copyright laws in your country before recording from records, CDs, radio, etc. Recording copyright-protected material may infringe on copyright laws. REC OUT (A-S500 only) 1 Rotate the REC OUT selector on the front panel to select the source you want to record (A-S500 only). Note When using the A-S300, the current input source will be recorded. 2 Play the source and begin recording using the recording device connected to the REC output jacks (LINE 2 and/or LINE 3) on the rear panel. See page 5. y A-S500 only: While recording, you can select another input source using the INPUT selector or the remote control and listen to another input source without affecting recording. OPERATION English 9 En PLAYING BACK TUNES FROM YOUR iPhone/iPod PLAYING BACK TUNES FROM YOUR iPhone/iPod Once you have connected an optional Yamaha Universal Dock for iPod or Wireless System for iPod to the DOCK jack on the rear panel of this ...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - A-S500 (4.17 mb)