valutazioni - 4, GPA: 3.8
(
)
)
|
Foto e specifiche Yamaha AX-397 |
Facilità d'uso
and Europe models) First, tighten the knob and then insert the banana plug into the end of the corresponding terminal. Banana plug 2 Unscrew the knob. Red: positive (+) Black: negative (-) Notes One or two speaker sets can be connected to this unit. If you use only one speaker set, connect it to either the SPEAKERS A or B terminals. Use speakers with the specified impedance shown on the rear panel of this unit. 3 Insert one bare wire into the hole in the side of each terminal. Red: positive (+) Black: negative (-) 4 Tighten the knob to secure the wire. Red: positive (+) Black: negative (-) m 3 l s 9 CONNECTIONS Connecting the power supply cord ■ Connecting the AC power supply cord Plug the power supply cord into the AC wall outlet after all other connections are complete. ■ AC OUTLET(S) (SWITCHED) U.K. and Australia models.....................................1 outlet Korea model..............................................................None Other models........................................................3 outlets Use these outlets to connect the power cords from your other components to this unit. The power to the AC OUTLET(S) is controlled by POWER or STANDBY/ON on the front panel of this unit (or on the remote control). The outlet(s) supply power to any connected component whenever the power of this unit is turned on. For information on the maximum power (total power consumption of components), see “SPECIFICATIONS” on page 18. ■ VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging the power supply cord into the AC wall outlet. Voltages are as follows: Asia model..........................AC 220/230-240 V, 50/60 Hz General model......AC 110/120/220/230-240 V, 50/60 Hz 10 PLAYING AND RECORDING Playing a source Note As for AX-397 only, if the TAPE MONITOR indicator on the front panel lights up when you listen to a source, press TAPE MONITOR on the front panel to turn off the TAPE MONITOR function (the TAPE MONITOR indicator turns off as a result). 1 Set VOLUME on the front panel counterclockwise to the extreme end. Press POWER on the front panel inward to the ON position. 3 Rotate the INPUT selector on the front panel (or press one of the input selector buttons on the remote control) to select the input source you want to listen to. The indicator of the selected input source lights up. C3 °ö"ö°ö B ö Ö Ö Front panel Remote control ♦ AUX MD TAPE CD/DVD TUNER PHONO @ @ @ @ ® @ >T\ Lights up 4 Press SPEAKERS A and/or B on the front panel to select speakers A and/or B. SPEAKERS Notes Both SPEAKERS A and B can be selected. If you listen with headphones, press both switches to release them outward to the OFF position. 5 Play the source. 6 Rotate VOLUME on the front panel (or press VOLUME +/- on the remote control) to adjust the sound output level. Remote control INPUT A B + or 2 ON OFF 11 PLAYING AND RECORDING 7 Adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls or the CD/DVD DIRECT AMP switch on the front panel. 'O' or o CD/DVD DIRECT AMP BALANCE LUUUNbSS •Ö1 Ci vô Note As for AX-497 only, you can also adjust the tonal quality by using PURE DIRECT on the front panel. Press STANDBY/ON on the front panel again (or STANDBY on the remote control) to finish using this unit and set it to the standby mode. The STANDBY indicator lights up. Front panel * Remote control STANDBY Lights up 8 or Note To completely cut off power supply from the AC wall outlet, press POWER on the front panel to release it outward to the OFF position. 12 PLAYING AND RECORDING Adjusting the tonal quality ■ Adjusting the BALANCE control Adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions. BALANCE ■ Using the CD/DVD DIRECT AMP switch Routes input signals from your CD or DVD player directly to the specially built-in amplifier for the CD or DVD player. As a result, the input signals bypass the INPUT selector and the BASS, TREBLE, BALANCE and LOUDNESS controls (and the TAPE MONITOR switch for AX-397 only) and then sent to the power amplifier, thus eliminating any alterations to the CD or DVD signals and creating the purest possible sound. Lights up ■ Using the PURE DIRECT switch (AX-497 only) Routes input signals from your audio sources. As a result, the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. RE DIREI Lights up Note As for AX-497 only, if both the CD/DVD DIRECT AMP and the PURE DIRECT switches are turned on, only the CD/DVD DIRECT AMP switch will function. ■ Adjusting the BASS and TREBLE controls Adjusts the high and low frequency response. BASS Increases or decreases the low frequency re...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - AX-497 (1.9 mb)