valutazioni - 3, GPA: 4 ( )

Produttore : Yamaha File Size : 423.02 kb File Nome : Lingua di insegnamento:

da questo dispositivo ha anche altre istruzioni :

Strumenti Musicali - AX-892 (2.63 mb)

CD DIRECT AMP switch: used to reproduce the purest CD sound . PURE DIRECT switch: used to reproduce the purest source sound . SUBSONIC FILTER switch; used to eliminate undesirable ultra-low-frequency signals (AX-592 and AX-892 only) . PRE OUT/MAIN IN terminals; useful for connecting an equalizer, sound processor, etc. (AX-592 and AX-892 only) . Remote control capability Supplied accessories l After unpacking, check that the following accessories are included. l Remote Control Transmitter l Batteries (size AA, R6, UM-3) YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX TAPE 2 TAPE 1A/B PLAY /CUT PLAYREC/PAUSEDIR A DIR B CD PHONO PLAYDISC POWER VOLUME TUNERA/B/C/D/EPRESET YAMAHA HiFi SYSTEM REMOTE CONTROL TRANSMITTER AUX TAPE 2 TAPE 1A/B PLAYREC/PAUSEDIR A DIR B CD PHONO PLAYDISC POWER VOLUME TUNERA/B/C/D/EPRESET AX-592/892 AX-492 English CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully and keep it in a safe place for future use. 2. Install this unit in a cool, dry and dust-free area. Do not place it in direct sunlight or near sources of heat (e.g., a stove, etc.). Make sure that it is well ventilated and not exposed to rain or moisture and that it is on a flat, stable surface, free from vibration. 3. Never open the cabinet. If something drops into the unit, contact your dealer. 4. When moving the unit, first disconnect the AC power plug and the cables which are connected to other equipment. Never pull the cables or use excessive force on switches or controls. 5. The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly, damaging the unit or causing a fire. Avoid blocking the ventilation openings and make sure that the unit is well ventilated. Allow at least 30 cm (12 in) of space above the unit and 20 cm (8 in) of space on the sides and rear. 6. Always set the VOLUME control to “°” before playing the source. Increase the volume gradually to a desired level after the source has started playing. 7. Use a clean, dry cloth to clean the unit. Do not use chemical solvents which might damage the finish. 8. Be sure to read the “TROUBLESHOOTING” section before deciding that the unit is faulty. 9. When not planning to use this unit for long periods of time (e.g., vacation, etc.), disconnect the AC power plug from the electrical outlet. 10. To prevent damage from lightning, disconnect the AC power plug and antenna cable when there is an electrical storm. 11. Make sure that the unit is always properly grounded and polarized. 12. Do not connect audio equipment to the AC outlet on the rear panel if the equipment requires more power than the outlet is rated to provide. 13. Voltage Selector (General Model only) The voltage selector on the rear panel of this unit must be set for your local main voltage beforeplugging into the electrical outlet. Voltages are 110/120/220/240 V AC, 60/50 Hz. WARNING To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. IMPORTANT The serial number is located on the rear panel. Please record the serial number of this unit in the space below. Serial No.: Keep this Owner’s Manual in a safe place for future use. Note The unit is not disconnected from the AC power source as long as it is connected to the electrical outlet, even if the unit itself is turned off. CAUTION (FOR CANADA MODEL) TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT. FOR CANADIAN CUSTOMERS THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCECAUSING EQUIPMENT REGULATIONS. WARNING Do not change the IMPEDANCE SELECTOR VOLTAGE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE POWER SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. Example: AX-892 IMPEDANCE SELECTOR AC OUTLETS A OR B : 4. MIN. /SPEAKER A + B : 8. MIN. /SPEAKER SWITCHIED 100W MAX. TOTAL A OR B : 6. MIN. /SPEAKER A + B :12. MIN. /SPEAKER CONNECTIONS . Before making any connections to or from this unit, first switch it and any other connected components off. . Properly connect this unit and other components, L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual of each component which is to be connected to this unit. . If you have YAMAHA components numbered 1, 2, 3, etc. on the rear panel, connections can easily be made by connecting the output (input) terminals of each component to the same-numbered terminals on this unit. AX-492 Turntable Tape deck 1 Tape deck 2 Speakers A Left electrical Compact disc player Tuner CAUTION SEE INSTRUCTION MANUAL FOR CONNECT SETTING PHONO CD TUNER R L L 1 2 TAPE 1 TAPE PB TAPE 2 (MD) AUX 3 REC OUT 4 TAPE PB 3 REC OUT 4 GND SPEAKERS AC OUTLETS SWITCHIED 100W MAX. T...

Scarica la tua

Per scaricare, digitare 2 cifre :