valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
2. Press the TEST switch. TEST 3. Turn up the volume on the You will hear a test tone pink noise) from speaker, then the center speaker, then the right main speaker, then the right surround speaker and then the left surround speaker, for about two seconds each. The display changes as shown below. (Left main) (Center) (Right main) (Right surround) (Left surround) NOTE: If not using a center speaker, be sure to set the function “1. CENTER SPEAKER” in the SET MENU mode to the PHNTM (phantom) position. You will then hear the center channel test tone from the left and right main speakers. CONTINUED English 17 4. When “TEST on the display, adjust the level of test tone from by pressing the PARAMETER + or – so that it becomes that of the main speakers. * While adjusting, the test-on the selected speaker. PARAMETER DSPDVD/LD Adjustable * Pressing “+” increases and “–” decreases the value. Pressing and holding the button will change the value continuously. 5. In the same way, when “TEST R SUR. ···dB” is shown on the display, adjust the level of test tone from the right surround speaker so that it becomes almost as same as that of the main speakers. 6. In the same way, adjust the level of test tone from the left surround speaker. 7. When adjustments are finished, press the TEST switch once again. NOTE: Once you have completed these use only the master VOLUME control to adjust the whole listening volume. Do not change any other volume setting in the system. ADJUSTMENTS The following nine types the performance of your system and your enjoyment for audio listening video watching. 1. CENTER SPEAKER 2. REAR SPEAKER 3. MAIN SPEAKER 4. LFE/BASS OUT 5. LFE LEVEL 6. CENTER DELAY 7. SURROUND DELAY 8. DYNAMIC RANGE 9. OUTPUT TRIM METHOD OF Operations should be information on this unit’s display panel. 1. Select the function (title) will make a change. SET MENU 2. Select any desired position or edit parameters on the function. PARAMETER In the same way, make a setting change or adjustment on any other function. English 19 DESCRIPTIONS 1. CENTER SPEAKER 3. MAIN SPEAKER 2. REAR SPEAKER 4. LFE/BASS OUT See pages 14 to 16 for details. (Once you have selected proper modes, you do not have to make a setting change until any alteration is made in your speaker system.) 5. LFE LEVEL (Adjusting the output level at the LFE (low frequency effect) channel) Control range: –20 dB to 0 dB (in 1 dB step) Preset value: 0 dB Adjusts the output level at the LFE (low frequency effect) channel. If the LFE signals are mixed with signals at other channels to output them from the same speakers, the ratio of LFE signal level to the level of other signals are adjusted. (See page 3 for details about the LFE channel.) 6. CENTER DELAY (Adjusting the of center sounds (dialog etc.)) Control range: 0 ms to 5 ms (in 1 ms step) Preset value: 0 ms Adjusts the delay between the main sounds (at the main channels) and dialog etc. (at the center The larger the value, the later the dialog etc. is generated. This is for making sounds from the left main, center and main speakers reach your listening position at the same time by delaying the sound from the center speaker if the distance from the center speaker to your listening position is shorter than the distance from the left or right main speaker to your listening position. 7. SURROUND DELAY (Adjusting the delay of rear surround sounds) Control range: 0 ms to 15 ms (in 1 ms step) Preset value: 15 ms Adjusts the delay between the main sounds (at the main channels) and surround sounds. (at the rear channel). The larger the value, the later the surround sounds is generated. English 8. DYNAMIC RANGE range) Choices: MAX/STD/Preset position: MAX MAX: “Dynamic range” is the difference between the maximum level and the minimum level of sounds. Sounds on a movie originally designed for movie theaters feature very wide dynamic range. Dolby Digital (AC-3) technology can bring the original sound track into a home audio format with this wide dynamic range unchanged. In this position, a source encoded with the Dolby Digital (AC-3) is reproduced in the original sound track’s wide dynamic range providing you with powerful sounds like a movie theater. Selecting this position will be more ideal if you can listen to a source in a high output level in a room specially soundproofed for audio/video enjoyment. STD (Standard): Powerful sounds of extremely wide dynamic range are not always suitable for home use. Depending upon the condition of your listening environment, it may not possible to increase the sound output level as high as a movie theater, however, in a level proper for listening to in your room, the low level parts of source sound cannot be heard as well because they will be lost among noises in your environment. Dolby Digital (AC-3) technology also makes it possible to reduce an original sound track’s dynamic range for a home audio format by “compressing” the data. In this position, a source encoded with the Dolby Digital (AC-3...