valutazioni - 2, GPA: 4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
GHPF (High Pass Filter) If this button is on, the LOW EQ will function as a high pass filter EQ. The Q knob of the LOW EQ will disappear, and the GAIN knob will act as the high pass filter on/off switch. H (HIGH shelving) If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disappear). ILPF (Low Pass Filter) If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear, and the GAIN knob will act as the low pass filter on/off switch. JON (On/off) Switches the EQ on/off. KLIBRARY Accesses the OUTPUT EQ page of the LIBRARY window. PM5D Editor Owner’s Manual 30 LTYPE I/TYPE II (EQ type) LTYPE I/TYPE II (EQ type) MEQ LINK GROUP Selects the EQ link group (A–F) to which that channel belongs. NUPPER/LOWER Switches the four bands affected by controls 3–9 between LOWER (1 LOW–4 HIGH) and UPPER (5 LOW–8 HIGH). .DELAY This is the same as for the delay settings of an input channel (. p.26). .DCA GROUP / MUTE GROUP / SAFE 1 2 3 ADCA GROUP Selects the DCA group (7/8) to which the MIX channel belongs. BMUTE GROUP Selects the mute group (1–8) to which the MIX channel belongs. CRECALL SAFE / MUTE SAFE These enable/disable Recall Safe and Mute Safe for the MIX channel. PM5D Editor Owner’s Manual 31 ..r 3 7 8 6 5 4 1 2 ATO ST (To stereo) This is an on/off switch for the signal sent from the MIX channel to the STEREO bus. The PRE button located below selects PRE (immediately before the MIX [ON] key) or POST (immediately after the MIX [ON] key) as the point from which the signal is sent from the MIX channel to the STEREO bus. BTO ST PAN (To stereo pan) Sets the panning of the signal sent from the MIX channel to the STEREO bus. CLCR Turns LCR mode on/off for each channel. If this is turned on for a channel, you can use the TO ST PAN (2) knob to simultaneously control the level of the signal sent to the STEREO bus L/R channels and CENTER channel. DCSR (Center Side Ratio) This adjusts the level ratio (0–100%) of the CENTER channel relative to the STEREO bus L/R channels. To change the value, drag upward or downward inside the numerical box. EBALANCE This adjusts the left/right output balance of paired channels. This is not shown if pairing is not specified. FON Switches the MIX channel on/off. This is linked with the MIX [ON] keys in the MIX section of the PM5D panel. GFader Adjusts the output level of the MIX channel. This is linked with the MIX encoders on the PM5D panel (if the [MIX MASTER] key is on). The current value is shown in the numerical box immediately below. HCUE This button cue-monitors the signal of the MIX channel. This is linked with the MIX [CUE] keys in the MIX section of the PM5D panel. PM5D Editor Owner’s Manual 32 ..X 1 2 3 4 5 AMATRIX send level This adjusts the send level of the signal sent from the MIX channel to the MATRIX buses. BPair This indicates the pairing status of adjacent odd-numbered/even-numbered MATRIX channels. You can click the heart symbol to enable/disable pairing. CON (MATRIX send on/off) This is an on/off switch for the signal sent from the MIX channel to the MATRIX bus. DPOINT (Send point) Selects the point from which the signal is sent from the MIX channel to the MATRIX bus. You can choose PRE FADER (immediately before the fader), POST FADER (immediately after the fader), or POST ON (immediately after the MIX [ON] key). ECH to MIX POST POINT Selects either POST ON or POST TO ST as the position from which the signal is sent from all input channels to the currently selected MIX bus. PM5D Editor Owner’s Manual 33 If a MATRIX channel is selected .CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a MATRIX channel, this is the same as for an input channel (. p.20). .COMPRESSOR Except for the fact that the COMP LINK GROUP is A–F, and that the types of signal that can be selected for key- in are different, this is the same as for the compressor of an input channel (. p.23). .INSERT Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings of an input channel (. p.24). .EQUALIZER Except for the fact that there is no LOWER/UPPER button, and that the EQ LINK groups are G/H, this is the same as for the equalizer of a MIX channel (. p.30). .DELAY This is the same as for the delay settings of an input channel (. p.26). .DCA GROUP / MUTE GROUP / SAFE These are the same as the DCA Group / Mute Group / Safe settings of a MIX channel (. p.31). PM5D Editor Owner’s Manual 34 ..r 2 1 3 4 ABALANCE This adjusts the left/right output balance of paired channels. This is not shown if pairing is not specified. BON This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys in the MATRIX section of the PM5D panel. CFader This adjusts the output level of the MATRIX channel. This is linked with the MATRIX encoders in the MATRIX section of the PM5D panel. The current value is shown in the numerical bo...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - PM5D (1.06 mb)