valutazioni - 4, GPA: 4 ( )

Produttore : Yamaha File Size : 1.64 mb File Nome : Lingua di insegnamento:

da questo dispositivo ha anche altre istruzioni :

Strumenti Musicali - M2500-32 (128.49 kb)

Strumenti Musicali - M2500-32 (1.65 mb)

Strumenti Musicali - M2500-32 (128.49 kb)

Strumenti Musicali - M2500-32 (4.29 mb)

Nominal input level is 0 dB. The pin wiring is as follows. Tip (send) 1/4" phone plug 1/4" phone plug 1/4" TRS phone plug To processor’s input From processor’s output Connect to INSERT I/O jack Tip (send) Ring (return) Sleeve (ground) Sleeve (ground) Tip (return) Sleeve (ground) 28 M2500—Owner’s Manual Rear panel M2500—Owner’s Manual 29 L MIDI connectors These are standard five-pin MIDI connectors. By connecting these to a sequencer or to the MIDI interface of a computer, scenes can be selected from an external device, or scene memories can be backed up. MIDI IN connector MIDI data is received at this connector. Use a MIDI cable to connect this to the MIDI OUT connector of your external MIDI device. MIDI OUT connector MIDI data is transmitted from this connector. Use a MIDI cable to connect this to the MIDI IN connector of your external MIDI device. MIDI THRU connector Data received at the MIDI IN connector is re-transmitted without change from this connector. For example if you have connected three M2500 units via MIDI as shown below, switching scenes on the master M2500 (1) can cause the slave M2500 units (2/3) to switch scenes in the same way. M PHANTOM MASTER switch This is the master switch for the +48 V phantom power supply. N DC POWER INPUT connector Connect the supplied PW3000MA power supply to this connector to supply power to the M2500. By connecting two PW3000MA units to the M2500 as shown in the following diagram, you can ensure a stable supply of power. In this case, each PW3000MA will supply 50% of the power to the M2500. In the unlikely event that one of the PW3000MA units fail, the other PW3000MA will automatically supply 100% of the power to the M2500. O LAMP connector This is an XLR-4-31 (four-pin female) output connector that supplies power to the optional lamp. The M2500-24/32 have two LAMP connectors, and the M2500-40C/48C/56C have three LAMP connectors. Note: The PW3000M power supply cannot be used with the M2500 mixer. Note: Before connecting or disconnecting the power supply cable, make sure that the power of the PW3000MA is turned off. .......... 1 .......... 2 .......... 3 ................ .............. .................. .............. PHANTOM MASTER READ OWNER’S MANUAL DC POWER INPUT OFF ON N M DC POWER INPUT .......... DC PARALLEL INPUT DC OUTPUT DC PARALLEL INPUT DC OUTPUT ................ ................ ............................ .................. .................. .................................. LAMP O The Scene Memory functio n What is scene memory? Scene memory is a function that stores the on/off status of the monaural/stereo input channels, the G1/ A7–G8/14 section, the STEREO section, and the MONO/C section as one of 128 “scenes.” A scene that has been stored can be easily recalled at any time. Program change messages received at the MIDI IN connector can also recall scenes, and when a scene is recalled, a corresponding program change message can be transmitted from the MIDI OUT connector. With the factory settings, the scenes stored in the M2500 are set as follows. Of these, scene memory numbers 1–128 can be rewritten, and 129 and 130 are for recall only. Scene memory number Contents 1 All on 2 All off 3 All on 4 All off 5 All on 6 All off 7 All on 8 All off 9–128 No data 129 All on 130 All off Scene memory operations are performed in the Control section. For details on the parts of the control section and their function, refer to page 22. Note: With the factory settings, the M2500 will start up with scene memory number 1 recalled. Modes of the scene memory function The Scene Memory function has the following three modes. Normal mode This is the normal operating mode in which scenes are recalled and stored. When the M2500 is in Normal mode, the indicators of the CHECK switch and UTILITY switch in the control section will be dark. For details on operation in Normal mode, refer to page 31. Check mode In this mode you can check the contents of a scene before you recall it, or edit the on/off settings of a saved scene without changing the current on/off status. In Check mode, the indicator of the CHECK switch will be lit. For details on operation in Check mode, refer to page 32. Utility mode In this mode you can make various settings related to scene memory and MIDI. In Utility mode, the indicator of the UTILITY switch will be lit. For details on operation in Utility mode, refer to page 34. 30 M2500—Owner’s Manual The Scene Memory function The Scene Memory function Recalling a scene 1. Use the / switches or the 0–9/ENTER switches of the control section to make the MEMORY display show the scene memory number that you wish to recall. The selected scene memory number will blink. Note: • Scene memory numbers 129 and 130 can be selected only by the 0–9/ENTER switches. • If the mute groups (page 37) are being used, scene memory numbers 1–8 can be selected only by the 0–9/ENTER switches. 2. Press the RECALL switch. The scene of the selected scene memory number will...

Scarica la tua

Per scaricare, digitare 2 cifre :