valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
• Do not block the power supply unit ventilation slots. The power supply unit has ventilation slots at the front to prevent the internal temperature from rising. Blocked ventilation slots are a fire hazard. • Leave a reasonable amount of free-air space around the power supply unit. • If the power supply unit is to be rack mounted, leave at least 10 cm free above the top panel and behind the rear panel. When the power supply unit is in use, remove the rear of the rack, or open its ventilation slots to prevent overheating, which could be a fire hazard. • Do not try to modify the power supply unit. This could be a fire and electrical shock hazard. • The power supply unit operating temperature is between 5°C and 35°C (41°F and 95°F). • Turn off all audio devices and speakers when connecting to the power supply unit. Refer to the owner’s manual for each device. Use the correct cables and connect as specified. • If you notice any abnormality—such as smoke, odor, or noise—turn off the power supply unit immediately. Remove the power cord from the AC outlet. Confirm that the abnormality is no longer present. Consult your dealer for repair. Using the power supply unit in this condition is a fire and shock hazard. • If a foreign object or water gets inside the power supply unit, turn it off immediately. Remove the power cord from the AC outlet. Consult your dealer for repair. Using the power supply unit in this condition is a fire and electrical shock hazard. • If you plan not to use the power supply unit for a long period of time, remove the power cord from the AC outlet. Leaving the power supply unit connected is a fire hazard. • Do not use benzene, thinner, cleaning detergent, or a chemical cloth to clean the power supply unit. Use only a soft, dry cloth. • The power supply unit uses high-frequency digital circuits that may cause interference on radios and televisions placed close to it. If interference does occur, relocate the affected equipment. For European Model Purchaser/User information specified in EN55103-1 and EN55103-2. Inrush Current: 44A Conformed Environment: E1, E2, E3 and E4. l POWER OPERATION MONITOR POWER SUPPLY ON/ OFF NORMAL +48V +12V +15V –15V 1 2 Rear panel The PW3000MA power supply should be installed in a well ventilated location. In particular, the front and rear panels must not be blocked, since the ventilation path passes through them. A POWER ON/OFF switch After connections to the mixer have been completed, turn this switch on to supply power to the mixer. B Operation monitor These LEDs indicate the status of the four types of power that are being supplied to the mixer. Normally (i.e., when no malfunction has occurred), the green LEDs (NORMAL) will light. If a malfunction occurs, the LED for that section of the power supply will go dark. Turn the power off and wait for a time before turning the power on again. If the same LED(s) are dark, contact a Yamaha service center. C GND terminals This is the grounding screw terminal. If hum or noise occurs, ground (earth) the unit via this jack, or try connecting it to the chassis of the other device. D DC OUTPUT connector Connect this connector to the mixer to supply power to it. DC OUTPUT CONNECT DISCONNECT PIN 2 +15V 5.0A PIN 5 –15V 5.0A PIN 6 +12V 5.0A PIN 9 +48V 0.2A DC PARALLEL INPUT CONNECT DISCONNECT 5 4 3 E DC PARALLEL INPUT connector This connector allows two PW3000MA units to be connected in parallel. As shown in the following diagram, use the included parallel connection cable to make connections. In this case, the two PW3000MA units will each supply 50% of the power in normal operation. Even in the unlikely event that one of the PW3000MA units failed, the other PW3000MA will supply 100% of the power, ensuring an uninterrupted power supply. DC OUTPUT CONNECT DISCONNECT PIN 2 +15V 5.0A PIN 5 –15V 5.0A PIN 6 +12V 5.0A PIN 9 +48V 0.2A DC PARALLEL INPUT CONNECT DISCONNECT DC OUTPUT CONNECT DISCONNECT PIN 2 +15V 5.0A PIN 5 –15V 5.0A PIN 6 +12V 5.0A PIN 9 +48V 0.2A DC PARALLEL INPUT CONNECT DISCONNECT PW3000MA PW3000MA DC POWER INPUT DC OUTPUT DC OUTPUT DC PARALLEL INPUT The PW3000MA power supply can be used with the following mixers. M2500-56C M3000A-56C M2500-48C M3000A-40C M2500-40C M3000A-32 M2500-32 M3000A-24 M2500-24 s Power Requirements USA and Canada: 120 V, 60 Hz Europe: 230 V, 50 Hz Others: 240 V, 50 Hz Power Consumptions USA and Canada: 500 W, 600 VA Europe: 500 W Others: 500 W Dimension (W x H x D) 480 mm x 103.5 mm x 455 mm Weight 15 kg Accessories Parallel connection cable (1 m) Power supply cable pin configuration Pin No. Signal name 1 Power supply remote 2 +15 V 3 ±15 V GND 4 +48 V GND 5 –15 V 6 +12 V 7 +12 V GND/ power supply remote 8 Power supply remote 9 +48 V 10 FRAME GND Power supply connector DC PARALLEL INPUT DC OUTPUT 123 8910 5 467 321 1098 6 754 Dimensions D:455 W:480 88H:103.5 56.8 292 308 49.4 405.6 Units: mm • Specifications and appearance are subject to change without notice for improvement. Mode d’emploi Francai...