|
Facilità d'uso
The MODERN setting increases the overall gain and notches (cuts) the mid frequencies, establishing a modern tone often associated with Hard Rock and Metal styles. The CLASSIC setting emulates overdriven tube sounds of the past. The HIGH GAIN setting increases the overall gain and changes the EQ, creating a tighter response at lower Pre Gain settings or an “over the top” sound at higher Pre Gain settings. Experiment with this switch setting while adjusting the Lead EQ (9) to help you obtain your desired tone. Refer to page 12 for suggested settings. LEAD EQ These passive tone controls regulate the low, mid, and high frequencies of the Lead channel. POST GAIN Use this control to set the overall level of the Lead channel once your tone has been achieved. REVERB The Reverb control adjusts the overall reverb level. VOLUME BOOST This knob functions as a limited master volume control without the footswitch. For solo's and loud passages, use the footswitch to boost the volume by 0 - 10dB. POWER LED This LED illuminates indicating the amp is on. POWER SWITCH (Located on the rear panel of the Envoy 110.) To apply power to the unit, press the switch to the "on" position. The LED (13) will illuminate, indicating power is being supplied. Front Panel 13 12 11 10 8 9 10 14 13 12 11 8 9 8 9 10 11 12 13 14 9 10 Rear Panel 17 16 14 15 15 17 15 AC POWER INLET (Power Cord Located Under Chassis) This is the receptacle for an IEC line cord, which provides AC power tot the unit. Connect the line cord to this connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See voltage marking on unit.) Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always make sure that the amplifier and all associated equipment is properly grounded. NOTE: FOR UK ONLY As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored green and yellow must be connected to the terminal which is marked by the letter E, or by the earth symbol, or colored green or green and yellow. (2) The wire which is colored blue must be connected to the terminal which is marked with the letter N, or the color black. (3) The wire which is colored brown must be connected to the terminal which is marked with the letter L, or the color red. To avoid the risk of electrical shock, do not place fingers or any other objects into empty tube sockets while power is being supplied to unit. HEADPHONE JACK (Envoy 110 ONLY) This stereo 1/4” jack accepts a standard pair of headphones. Using this jack defeats the output to the speaker making it ideal for quiet practice applications. SPEAKER SIMULATED DIRECT OUTPUT The signal produced in this convenient 1/4" direct output jack is specifically voiced to accurately simulate speaker cabinet response. The output can be used for direct recordings or sent to a mixer or PA system. Users can adjust output levels with the adjacent control knob (Bandit 112 Only). 16 17 POWER LEVEL (Bandit 112 ONLY) This switch provides three power level options: 25%, 50% and 100%. This circuit is actually a patented tube power amplifier simulator that "squashes" the signal. Use as desired for different playing environments, for example an apartment at 25% or live big at 100%. EXTERNAL SPEAKER JACK (Bandit 112 ONLY) This 1/4” jack is provided for the connection of an external speaker cabinet. The minimum external speaker impedance is 8 ohms. DAMPING (Bandit 112 ONLY) This three position switch offers damping level adjustment; loose, medium and tight. EFFECTS LOOP (Bandit 112 ONLY) This pair of mono 1/4” jacks provides an effects SEND and RETURN path for the preamp signal. Connect the SEND jack to the input of an external, low-level, signal processing effects unit. Return the signal from your external effects unit to the RETURN jack. This setup is known as an Effects Loop since the signal exits your amp (send) and loops (return) back to it. REMOTE SWITCH The multi-functional remote footswitch is used to select between the Clean and Lead channels as well as to boost the volume. NOTE: On both units, the Channel Select Switch (6) must be in the LEAD position for the Remote Switch to work. Rear Panel 22 18 22 20 19 21 18 19 20 21 22 Suggested Settings Clean/MetalJazz/Moderate DistortionClean Blues/Dirty Blues Clean Metal Clean Channel: Volume: As Desired Classic Low: 7-9 Mid: 2-4 High: 5-7 Lead Channel: Pre Gain: 8-10 High Gain/ModerateClassic: Moderate Low: 8-10 Mid: 0-2 High: 6-8 Post Gain: As Desired Master Section: Reverb: As Desired Boost: As Desired for solo level Clean/MetalJazz/Moderate DistortionClean Blues/Dirty Blues Jazz Moderate Distortion Clean/MetalJazz/Moderate D...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - ENVOY 112 (2.88 mb)