valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. 2 RS502 Owner’s Manual RS502 Owner’s Manual 3 After opening up the package containing your electronic drum rack, please verify that all of the following components are present. Package Contents Main frame (x1) Left arm (x1) Right arm (x1) Left leg (x1) Right leg (x1) Tom holder (x3) Cymbal holder (x2) Snare holder (x1) Owner’s Manual (this booklet) 4 RS502 Owner’s Manual . Fully-assembled rack Left arm Clamp r Clamp e Clamp w Clamp t Right arm Left leg Right leg Main frame Clamp q RS502 Owner’s Manual 5 1. Lay the main frame down on a solid, level surface and loosen the screws in clamps q and w using the tuning key. 2. Loosen the bolts on clamps q, w, and e and move the clamps all the way down to the center strut. Following this, lightly tighten the clamp bolts. 3. Take the left arm from the package and loosen the screw in clamp r using the tuning key. Assembling the Rack NOTE The tuning key can be found in the pad set package. The left and right arms look very alike, but the left arm is longer. Take care not to mix them up when assembling the rack. Clamp q Clamp w Screw Tuning key Screw Tuning key Clamp q Clamp e Center strut Clamp w Loosen Bolt Lightly tighten Left arm Clamp r Screw 6 RS502 Owner’s Manual 4. Push the left arm as far as it will go into clamp q on the main frame. When inserted, ensure that the arrow sticker ( . ) on the left arm is lined up with the slit in clamp q. 5. Securely tighten the screw in clamp q using the tuning key. 6. Take the left leg from the package and push it as far as it will go into clamp r. 7. Securely tighten the screw in clamp r using the tuning key. The left and right legs look very alike, but the left leg is shorter. Take care not to mix them up when assembling the rack. Left arm Arrow Clamp q Slit Left arm Clamp q Screw Left leg Clamp r Screw RS502 Owner’s Manual 7 8. Take the right arm from the package and push it as far as it will go into clamp w. When inserted, ensure that the arrow sticker ( . ) on the right arm is lined up with the slit in clamp w. 9. Securely tighten the screw in clamp w using the tuning key. 10. Loosen the bolt on clamp t. 11. Take the right leg from the package and insert it into clamp t. When inserted, ensure that the right leg protrudes from the clamp by approximately 7 cm. 12. Securely tighten the bolt on clamp t. Right arm Arrow Clamp w Slit Screw Clamp t Right arm Clamp w Clamp t Bolt Clamp t Right arm Right leg 7 cm Bolt 8 RS502 Owner’s Manual 13. Lift up the main frame and open up the left arm, the right arm, and the snare arm. 14. Securely tighten the bolts on clamps q, w, and e. 15. Check all bolts and screws once again and ensure that they are tightly fastened. CAUTION Do not open up the rack’s left and right legs any more than shown in the figure below. Failure to observe this precaution can lead to the rack toppling over and causing injury. Right arm Left arm Snare arm 1,100 mm 130° 130° Clamp q Clamp w Bolt Clamp e Bolt Bolt RS502 Owner’s Manual 9 1. Loosen the bolts on the following seven clamps (A to G) and rotate or move the clamps to the positions shown below. Following this, securely tighten all of the bolts to lock the clamps in place. • One snare clamp (A) • Three tom clamps (B, C, and D) • Two cymbal clamps (E and F) • One drum module clamp (G) Attaching the Holders NOTE Tom clamp D should be moved but not rotated. (All other clamps are rotated.) G E B C A F D Tom clamps (x3) Drum module clamp Snare clamp Cymbal clamps (x2) 10 RS502 Owner’s Manual 2. Attach a tom holder to each of the three tom clamps. 2-1. Loosen the bolt on the tom clamp. 2-2. Insert the tom holder. 2-3. Securely tighten the bolt on the tom clamp. 3. Attach a cymbal holder to each of the two cymbal clamps. 3-1. Loosen the bolt on the cymbal clamp. 3-2. Insert the cymbal holder. 3-3. Securely tighten the bolt on the cymbal clamp. CAUTION Take special care with tom holders as they have sharp tips that could cause injury. NOTE When tightening the bolt, ensure that the black sleeve is positioned inside the clamp’s mounting hole and securely held. Tom clamp Tom holder Bolt Cymbal holder Bolt Cymbal holder Bolt Cymbal clamp Cymbal clamp Sleeve (black) .On the left arm . On the right arm Sleeve (black) 4. Attach the snare holder to the snare clamp. CAUTION Take special care with the snare holder as the rod has a sharp tip that could cause injury. Bolt Snare clamp Snare holder 4-1. Loosen the bolt on the snare clamp. 4-2. Insert the snare holder. 4-3. Securely tighten the bolt on the snare clamp. If going on to assemble a Yamaha electronic drum kit, please refer to the Assembly Manual booklet that came with your pad set. Troubleshooting • The rack is unstable even though placed on a level surf...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - DTX532K (4.82 mb)
Strumenti Musicali - DTX562K (4.82 mb)