valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Use the [UP]/[DOWN] buttons to set the type of parameter you want controlled. • oFF : off (no control) • bAL : Balance between the DIRECT tone and the MIC tone (BLEND) • StE : The stereo position of the two mics (STEREO) • A. Pr : Post pre-amp volume • A. rE : Post reverb volume • bAS : Tone Control (BASS) • mid : Tone Control (MIDDLE) • trE : Tone Control (TREBLE) • PrE : Tone Control (PRESENCE) • Lmt : Limiter Level • SPd : SPEED/TIME settings for the Chorus/ Delay Effects • dPt : DEPTH/FEEDBACK settings for the Chorus/Delay Effects • LE : LEVEL setting for the Chorus/Delay Effects • rE : REVERB setting for the Reverb Effect The controller that is set in step 3 of this proce dure can control the above parameters (setting values). 5. Press the [FR 3] button The minimum parameter value (the controller’s minimum parameter value) will appear in the display. Use the [UP]/[DOWN] buttons to set the value (0.0-10.0). 6. Press the [FR 4] button The maximum parameter value (the controller’s maximum parameter value) will appear in the display. Use the [UP]/[DOWN] buttons to set the value (0.0-10.0). 7. Press the [UTILITY] button to return to the Play Mode. These external control settings are stored with patch data. Also, in the Utility Mode, there is a function that is not related to patch data settings that sets the Utility Mode’s External Control to always ON (effective) or always OFF. (> page 26) Tuner Mode This mode is used for tuning your guitar. In the Tuner Mode, the AG-Stomp operates like a chromatic auto tuner. ¦ Enter the Tuner Mode To enter the Tuner Mode, use any one of the three methods described below. • In the Play Mode, press the [UTILITY] and [STORE] buttons simultaneously. • In the Play Mode, hold the BANK switch until “tu” appears in the display. (The Tuner Mode comes after the Bank Select Mode.) • In the Bank Select Mode, hold the BANK switch until “tu” appears in the display. In the Tuner Mode, all outputs on the AG- Stomp (OUTPUT, PHONES, DIGITAL OUT) will be muted (no sound will be produced. ¦ Tuning The name of the note closest to that of which you played will appear in the display, and the five lamps will be used to indicate whether the note’s pitch is high or low. 1. Use the [UP]/[DOWN] buttons to change the standard pitch. (Refer to the following “Setting the Standard Pitch” section.) 2. Play the note you want tune (play only a single note). • At first, roughly tune the guitar so that the name of the note you want to tune appears in the display. Note names are indicated in the display as follows: ABb CDb DEb EF Gb GAb A bb C db d EbE F GbG Ab • If the pitch is low, the FEEDBACK REDUCTION 1 and 2 lamps will light while the FEEDBACK REDUCTION 3 lamp flashes. If the pitch is high, the FEEDBACK REDUCTION 4 and 5 lamps will light while the FEEDBACK REDUCTION 3 lamp flashes. Finely tune the note until only the FEEDBACK REDUCTION 3 lamp lights, then tuning is complete. (At this time the BANKS Switch’s lamp will also light.) Tuning is complete! Raise Lower the pitch the pitch Light Flash Flash Light 3. Press the [UTILITY] button or the BANK Switch to return to the Play Mode. ¦ Setting the Standard Pitch Usually the tuner’s standard pitch is set to A=440Hz, however there are some cases where the standard pitch of an acoustic piano, etc. is set to a pitch other than 440Hz. The AG-Stomp’s standard pitch can be set to a pitch anywhere between 436Hz and 444Hz. 1. In the Tuner Mode, press the [UP] or [DOWN] button to display the standard pitch in the display. * When the AG-Stomp’s power is switched ON, the standard pitch is automatically set to 440Hz. 2. Every time the [UP] button is pressed, the standard pitch will increase by 1Hz, and every time the [DOWN] button is pressed, the standard pitch will decrease by 1Hz. Utility Mode The Utility Mode is used for the AG-Stomp’s overall system settings for things such as the footswitch, MIDI, external controllers, EXP. PEDAL jack, etc. * In the following section, the abbreviation [FR 1] button refers to the [FEEDBACK REDUCTION 1] button, etc. ¦ About the Utility Mode When in the Play Mode, press the [UTILITY] button to enter the Utility Mode (the lamp lights). When in the Utility Mode, press the [UTILITY] button to return to the Play Mode (the lamp turns off). In the Utility Mode, MIDI messages cannot be received. Use the Play Mode to receive MIDI messages. Also, individual Utility Mode settings are saved when the Utility Mode is exited. In the Utility Mode, it is possible to set the following five functions. Use the MIC TYPE Select Switch to select the function. 1: Footswitch Functions 2: MIDI Functions 3: External Control Settings 4: EXP Pedal Settings 5: Feedback Reduction Operating Mode ¦ Footswitch Functions Press the [UTILITY] button and set the MIC TYPE Select Switch to CONDENSER 1 (“F.S” will appear in the display). . Select the Footswitch function. Press the [LIMITER] button and use the [UP]/ [DOWN] buttons to set the function of Footswitches (1-3). ...