valutazioni - , GPA: ( )

Istruzioni per l'uso Delta, Modello 66-500-1

Produttore : Delta
File Size : 1.39 mb
File Nome : 262bf7dd-d142-4f8e-b979-918d3597d35b.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

oil leaks will damage carpet, paint or other surfaces in vehicles or trailers. HOW TO PREVENT IT Always place COMPRESSOR on a protective mat when transporting to protect against damage to vehicle from leaks. Remove COMPRESSOR from vehicle immediately upon arrival at your destination. HAZARD WARNING: RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT Unsafe operation of your air compressor Review and understand all instructions could lead to serious injury or death to and warnings in this manual. you or others. Become familiar with the operation and controls of the air compressor. Keep operating area clear of all persons, pets, and obstacles. Keep children away from the air compressor at all times. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times. Never defeat the safety features of this product. Equip area of operation with a fire extinguisher. Do not operate machine with missing, broken, or unauthorized parts. 7- ENG D27449 GLOSSARY Become familiar with these terms before operating the unit. CFM: Cubic feet per minute. SCFM: Standard cubic feet per minute; a unit of measure of air delivery. PSIG: Pounds per square inch gauge; a unit of measure of pressure. Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety. Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use your accessory. When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called “cut-in” pressure. Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called “cut-out” pressure. Branch Circuit: Circuit carrying electricity from electrical panel to outlet. DUTY CYCLE Air compressors should be operated on not more than a 50% duty cycle. This means an air compressor that pumps air more than 50% of one hour is considered misuse, because the air compressor is undersized for the required air demand. Maximum compressor pumping time per hour is 30 minutes. SPECIFICATIONS Model No. 66-500-1 Horsepower Peak 2 Bore 1.875" Stroke 1.250" Voltage/Hertz/ Phase 120V/60Hz/1Ph Minimum Branch Circuit Requirement 15 amps *Fuse Type Time Delay Air Tank Capacity 8 gallons Approximate Cut-in Pressure 100 Approximate Cut-out Pressure 125 SCFM @ 40 PSIG 3.7 SCFM @ 90 PSIG 2.6 A circuit breaker is preferred. Use only a fuse or circuit breaker that is the same rating as the branch circuit the air compressor is operated on. If compressor is connected to a circuit protected by fuses, use only time delay fuses. Time delay fuses should be marked "D" in Canada and "T" in the US. ACCESSORIES Accessories for this unit are available at the store the unit was purchased. D27449 8- ENG ASSEMBLY (does not apply to all units) Assembly for “Tank” units The wheels and handle do not provide adequate clearance, stability or support for pulling the unit up and down stairs or steps. The unit must be lifted, or pushed up a ramp. 1. Submerge handle grip into warm soapy water to make installation easier. Remove handle grip from soapy water and slide onto handle. 2. Slide handle through holes in compressor saddle onto tabs. Secure with screws, one on each side. It will be necessary to brace or support one side of the outfit when installing the wheels because the compressor will have a tendency to tip over. 3. Install one shoulder bolt and one nut for each wheel. Tighten securely. The outfit will sit level if the wheels are properly installed. 4. Clean and dry underside of air tank leg opposite wheels. Remove the protective strip from the adhesive Wheel Shoulder Bolt Nut Compressor Saddle Tab backed molded foot bumpers. Attach the foot bumpers to the bottom of leg on each end. Press firmly into place. Molded Foot Bumpers INSTALLATION HOW TO SET UP YOUR UNIT Location of the Air Compressor Locate the air compressor in a clean, dry and well ventilated area. The air compressor should be located at least 12" away from the wall or other obstructions that will interfere with the flow of air. The air compressor pump and shroud are designed to allow for proper cooling. The ventilation openings on the compressor are necessary to maintain proper operating temperature. Do not place rags or other containers on or near these openings. 9- ENG D27449 GROUNDING INSTRUCTIONS RISK OF ELECTRICAL SHOCK. In the event of a short circuit, grounding reduces the risk of shock by providing an escape wire for the electric current. This air compressor must be properly grounded. The portable air co...