valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
It is wired for 120 volt operation. Instructions for converting the motor for 240 volt operation can be found on a label attached to the side of the motor, or as follows: bwmiwlI When converting the compressor for 240 volt operation, the three-pronged 120 volt cord plug must be replaced with a three-pronged 240 volt plug (purchase plug locally or order 892545 cord and plug assembly). GROUNDING INSTRUCTIONS The air compressor is equipped with a cord having a grounded wire with an appropriate grounding plug. The plug must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances. The outlet must have the same configuration as the plug. DO NOT USE AN ADAPTER. rmililiim« IMPROPER GROUNDING CAN RESULT IN SEVERE ELECTRICAL SHOCK. Inspect the plug and cord before each use. Do not use if there are signs of damage. Do not modify the plug that has been provided. If it does not fit the available outlet, the correct outlet should be installed by a qualified electrician. If these grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician. EXTENSION CORDS Use extra air hose instead of an extension cord to avoid voltage drop and power loss to the motor. If an extension cord must be used, be sure it is: • A 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the compressor. • In good condition. • No longer than 50 feet. • 12 gauge (AWG) or larger. (Wire size increases as gauge number decreases.) 10 AWG and 8 AWG may also be used. DO NOT USE 14 AWG or SMALLER. ADDITIONAL REGULATORS AND CONTROLS Since the air tank pressure is usually greater than that which is needed, a regulator is employed to control the air pressure ahead of any individual air driven device. Separate air transformers which combine the function of air regulation, moisture and dirt removal should be used where applicable. LUBRICATION The bearings in this unit are sealed bearings which contain sufficient lubricant to last their lives. No other lubrication is required. BREAK-IN PROCEDURES NOTE: Serious damage may result if the following break-in instructions are not closely followed. This procedure is required: Before the air compressor is put into service, after replacing the check valve, and when the piston or the cylinder sleeve is replaced: a. Set the pressure switch lever to the “OFF” position. b. Plug the power cord into the correct branch circuit receptacle. 10 c. Turn either drain valve (J) Fig. 4, opening it fully, to prevent air pressure build-up in the tank. d. Move the pressure switch lever to “ON/AUTO”. The compressor will start. e. Run the compressor for 15 minutes. Make sure the drain valve is open and there is no tank pressure build-up. f. After 15 minutes, close the drain valve by turning knob. The air receiver will fill to cut-out pressure and the motor will stop. The compressor is now ready for use. OPERATING PROCEDURES Preparation for Use: 1. Before attaching air hose or accessories, make sure the OFF/AUTO lever is set to “OFF” and the air regulator is closed. 2. Inspect air intake filter (H) Fig. 1. Clean or replace as necessary. 3. Attach hose and accessories. PMMililHlll TOO MUCH AIR PRESSURE CAUSES A HAZARDOUS RISK OF BURSTING. CHECK THE MANUFACTURER’S MAXIMUM PRESSURE RATING FOR AIR TOOLS AND ACCESSORIES. THE REGULATOR OUTLET PRESSURE MUST NEVER EXCEED THE MAXIMUM PRESSURE RATING OF THE TOOL BEING USED. 4. Turn the OFF/AUTO lever to “AUTO” and allow tank pressure to build. Motor will stop when tank pressure reaches “cut-out” pressure. 5. Open the regulator by turning it clockwise. Adjust the regulator to the correct pressure setting. The compressor is ready for use. 6. Always operate the air compressor in well ventilated areas; free of gasoline or other solvent vapors. Do not operate the compressor near the spray area. After Use: 7. Set the “OFF/AUTO” lever to “OFF”. 8. Turn the regulator counterclockwise to set the outlet pressure to zero. 9. Remove the air tool or accessory. 10. Pull ring on Safety Valve (K) Fig. 3, and allow air to bleed from the tank. Release the ring when tank pressure is approximately 20 psi. 11. Drain water from both air tanks. Turn both drain valves (J) Fig. 4, counterclockwise to open. r^y/^h'iu'LM WATER WILL CONDENSE IN THE AIR TANKS. IF NOT DRAINED, WATER WILL CORRODE AND WEAKEN THE AIR TANKSCAUSING A RISK OF AIR TANK RUPTURE. DRAIN BOTH AIR TANKS AFTER USE. NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, and reinstalled. 12. After the water has been completely drained, turn drain valves clockwise to close. The air compressor can now be stored. 11 MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. Inspect air intake filter and clean or replace ...
Questo manuale è adatto anche per i modelli :attrezzature di pompaggio - 892551-992 (4.32 mb)