Log:
valutazioni - 2, GPA: 3.5 ( )

Istruzioni per l'uso HP, Modello Shertech GCCV2V

Produttore : HP
File Size : 263.47 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Figure 4 - Pressure Relief Valve Adjustment Protective cap Adjust pressure relief valve screw Loosen lock nut 9. To convert the relief valve to external relief, remove the 1/4 NPT pipe plug from the pump cover (Figure 5 & 7, Ref. No. 13) and discard. This plug is next to the relief valve. In the bottom of the 1/4 NPT hole, there is a second drilled and tapped Figure 5 - External Bypass Installation Optional external bypass plug Remove and discard plug Form L-4083 (1/06) 7 Shertech Operating Instructions, Performance, Bronze Models GCBN2V, GCBN3V, GCBN22V and GCBN33V Specifications and Parts Manual Cast Iron Models GCCV2V, GCCV3V, GCCV22V and GCCV33V Carbonator-Mount Rotary Close-Coupled External Gear Pumps Operation (Continued) hole of 1/4 size. An optional external bypass plug (Figure 5 & 7, Ref. No. 14 included) should be inserted in this hole and bottomed out. The open 1/4 NPT port must now be piped back to the tank or well downstream of the pump suction. 10. For operation of the pump with pressure relief valve in reverse rotation, the motor may be reversed, allowing for reverse rotation. Standard models are equipped with pressure relief valves and the pump can be run in reverse, however, the pressure relief valve will not function. For continuous reverse rotation, the cover plate must be rotated 180°. This is accomplished by removing the six cover plate screws, rotating the cover plate, and reattaching the screws. The relief valve should now be on the opposite side. This will allow operation of the pump with a functioning pressure relief valve in reverse rotation. Maintenance Make certain that the power source is disconnected before attempting to service or disassemble any components! If the power disconnect is out of sight, lock it in the open position and tag to prevent application of power. GENERAL Check the pump for proper operation daily, weekly, monthly, etc. If anything has changed (pump noise, motor noise, leaks, etc.) since the pump was new, the pump should be removed, examined and repaired if necessary. This is a difficult motor/pump to repair, therefore, only qualified electricians or service technicians should attempt to repair this unit. Improper repair and/or assembly can cause problems with the electric motor used with this unit. See General Safety Information. Retighten the ”V“ band clamp screw as necessary. Use Loctite or similar thread sealant if screw keeps coming loose. Rotary gear pumps must be drained completely if subject to freezing temperature and should not be operated until temperature permits. To store the pump, place a small quantity of light oil or some other storage preservative compatible with your application in the pump and rotate the shaft very slowly to work the oil throughout the gears and the body. DISASSEMBLY AND ASSEMBLY Refer to Figure 7 for parts identification during disassembly and assembly. [Assumes pump is separated from motor and that Oldham coupling (Ref. No. 24) is removed.] 1. Remove screws (Ref. No. 3) and cover (Ref. No. 2). Refer to INSPECTION procedures below. 2. Lift out idler shaft (Ref. No. 8). 3. Remove internal retaining ring (Ref. No. 12) from drive end of the pump body (Ref. No. 1) using TruArc-type internal snap-ring pliers. 4. Carefully pry out ceramic seat (Ref. No. 11) and then seal (parts of seal seat assembly using a suitable hooked tool). Form L-4083 (1/06) 8 Shertech Operating Instructions, Performance, Specifications and Parts Manual Bronze Models GCBN2V, GCBN3V, GCBN22V and GCBN33V Cast Iron Models GCCV2V, GCCV3V, GCCV22V and GCCV33V NOTE: If seal rubber has become bonded to the shaft, use a pliers to remove...

Questo manuale è adatto anche per i modelli :
attrezzature di pompaggio - Shertech GCCV3VV (263.47 kb)
attrezzature di pompaggio - Shertech GCBN33V (263.47 kb)
attrezzature di pompaggio - Shertech GCBN22V (263.47 kb)
attrezzature di pompaggio - Shertech GCBN2V (263.47 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie