valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
2. Make sure the outlet being used has the same configuration as the grounded plug. DO NOT USE AN ADAPTER. See illustration. Plug Grounded Outlets Grounding Pin 3. Inspect the plug and cord before each use. Do not use if there are signs of damage. 4. If these grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician. Risk of Electrical Shock. IMPROPER GROUNDING CAN RESULT IN ELECTRICAL SHOCK. Do not modify the plug provided. If it does not fit the available outlet, a correct outlet should be installed by a qualified electrician. Repairs to the cord set or plug MUST be made by a qualified electrician. 11- ENG D29495 Extension Cords If an extension cord must be used, be sure it is: • a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the product • in good condition • no longer than 50 feet • 16 gauge (AWG) or larger. (Wire size increases as gauge number decreases. 14, 12, 10, and 8 AWG may also be used. Voltage and Circuit Protection Refer to the specification chart for the voltage and minimum branch circuit requirements. Risk of Unsafe Operation. Certain air compressors can be operated on a 15 amp circuit if the following conditions are met. 1. Voltage supply to circuit must comply with the National Electrical Code. 2. Circuit is not used to supply any other electrical needs. 3. Extension cords comply with specifications. 4. Circuit is equipped with a 15 amp circuit breaker or 15 amp time delay fuse. NOTE: If compressor is connected to a circuit protected by fuses, use only time delay fuses. Time delay fuses should be marked "D" in Canada and "T" in the US. If any of the above conditions cannot be met, or if operation of the compressor repeatedly causes interruption of the power, it may be necessary to operate it from a 20 amp circuit. It is not necessary to change the cord set. D29495 12- ENG OPERATION Know Your Air Compressor READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Adapter Hose Adapter Air Outlet Safety Valve Off/Auto Switch Extension Tube e Gauge Air Hose Power Cord Female Air Chuck Blow Gun Drain Valve, Inflating Tapered not shown Needle Inflator Description of Operation Become familiar with these controls before operating the unit. Off/Auto Switch: Turn this switch to"Auto" to provide automatic power to the pressure switch and "OFF" to shut off power at the end of each use. Pressure Switch (not shown): The pressure switch automatically starts the motor when the air tank pressure drops below the factory set "cut-in" pressure. It stops the motor when the air tank pressure reaches the factory set "cut-out" pressure. Safety Valve: If the pressure switch does not shut off the air compressor at its "cut-out" pressure setting, the safety valve will protect against high pressure by "popping out" at its factory set pressure (slightly higher than the pressure switch "cut-out" setting). Outlet Pressure Gauge: The outlet pressure gauge indicates the air pressure available at the outlet side of the regulator. This pressure is controlled by the regulator and is always less than or equal to the tank pressure. Regulator: Controls the air pressure shown on the outlet pressure gauge. Turn knob clockwise to increase pressure and counterclockwise to decrease pressure. 13- ENG D29495 Female Tire Chuck: Attaches to the hose end to be used to inflate tires. Note: To ensure correct tire pressure use a tire pressure gauge. Hose Adapter: Attaches to hose end to allow the use of accessories. Blow Gun Adapter: Attaches to hose end or blow gun (sold separately, not shown) to allow the inflating needle to be used. Inflating needle: Attaches to blow gun adapter to be used to inflate sport balls. Tapered Inflator: Attaches to hose adapter or blow gun (sold separately) to be used to inflate toy inflatables/air mattresses. Extension Tube: Attaches to hose adapter or blow gun (sold separately) to be used for air blowing, drying, and for specialized inflating. Drain Valve (not shown): The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use. Cooling System (not shown): This compressor contains an advanced design cooling system. At the heart of this cooling system is an engineered fan. It is perfectly normal for this fan to blow air through the vent holes in large amounts. You know that the cooling system is working when air is being expelled. Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet. Check Valve (not shown): When the air compressor is operating, the check valve is "open", allowi...