valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
After service, open the air release valve, remove the plugs, allow any air to escape through the valve before tightening the valve again and replace the strainer grids. The pump is now primed with water again and may be turned on. (ILLUSTRATION NOT TO SCALE) WATER LEVEL HOSE CLAMP INSIDE OF POOL STRAINER PLUG UPPER PROTRUDING HOSE CONNECTION WATERDIRECTION WATERDIRECTION UPPER PUMP CONNECTION BOTTOM PUMP CONNECTION THREADED COVER FILTER CARTRIDGE INSIDE AIR RELEASE VALVE HOSE (106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007 106 SAVE THESE INSTRUCTIONS Page 8 SSTTAATTIIOONNAARRYY MMOOUUNNTTIINNGG OOPPTTIIOONNFILTER PUMP STATIONARY MOUNTING OPTION -- (3) x M6 HEXAGON HEAD BOLTS -- (3) x M6 HEXAGON LOCK-NUTS 145mm 145mm 145mm 145mm 145mm145mm There are three mounting holes located at the bottom of the filter-pump base. These holes are provided because various country’s regulations, especially in the European community, require the filter-pump to be secured to the ground or to a base in a permanent upright position. These three holes form a triangle pattern and are 145mm from each other. The holes are slotted with a 7mm width. The filter-pump can be mounted on a cement base or onto a wooden structure to prevent accidental falling over. Total assembly must exceed 18kg. The drawings on the following show two possible ways of upright mounting. The European norm EN 60335-2-41 requires this product be secured to the ground or to a base. (106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007 106 SAVE THESE INSTRUCTIONS Page 9 MMAAIINNTTEENNAANNCCEEIt is recommended that the filter cartridge be replaced at least every 2 weeks. 1. Make sure filter pump is not operating. Disconnect line cord. 2. To prevent water from escaping the pool, unscrew the strainer grids from the strainer connectors and insert the hat-like plugs into the strainer connectors. 3. In a counter-clockwise motion, remove threaded cover (3) and cover seal (4). Be careful not to lose the cover seal (4). 4. Remove filter cartridge (5) to clean it. The filter may be cleaned from the spray from a water hose. 5. Use judgement as to whether cartridge needs to be replaced. 6. Return cartridge to filtering position. 7. Return the seal (4) and threaded cover (3) to their original positions. Tighten the threaded cover (3) by hand only, twisting it in a clock-wise direction. 8. After service, open the air release valve, remove the plugs, allow any air to escape through the valve before tightening the valve again and replace the strainer grids. The pump is now primed with water again and may be turned on. FILTER CARTRIDGE CLEANING OR REPLACEMENT (106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007 106 SAVE THESE INSTRUCTIONS Page 10 PPOOOOLL MMAAIINNTTEENNAANNCCEECAUTION Concentrated chlorine solutions may damage the pool liner. Always follow the chemical manufacturer’s directions, and the health and hazard warnings. 1. Before emptying your pool for long term storage, or relocation, be sure the water is directed towards an acceptable drain water receptacle away from the house. Check local regulations for specific directions regarding disposal of swimming pool water. 2. After pool is empty of all water, disconnect all pool hoses (7) from pool and filter pump, simply reverse the set up instructions. 3. Remove filter cartridge as shown in the Filter Cartridge Cleaning section, steps 2 thru 4. 4. Remove the strainers (6) from the pool wall. Place the wall plugs into the hose connections. Loosen clamps (8) securing the strainers before removal. 5. Drain water from the filter pump housing. 6. Depending on the cartridge (5) usage, a new cartridge may be needed for next season, keep a spare available. 7. Cover the seal (4), air release valve O-ring (2) and hose seals (9) with petroleum jelly to preserve its resilience during storage. 8. Store the filter pump and accessories in a dry, cool storage location. 9. The original packing carton can be used for storage. POOL CARE AND CHEMICALS • All pools require care to keep the water clear and hygienically clean. With proper chemical control, your filter will help attain this objective. Consult your pool supply dealer for instructions regarding the proper use of chlorine, algaecide and other chemical agents required for sparkling clear water. • Keep pool chemicals away from children. • Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could occur. • Daily pH checking and chemical treatment of the water is very important and can not be overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required when filling the pool as well as during the season. Consult your local swimming pool supply store for instructions. • The season's first filling of the pool may have brackish water requiring extra water additives and extra filter changes. Do not allow swimming in pool until the pH level is balanced. Consult your local swi...