The valve can then be removed, cleaned, then reinstalled. 8. Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind them loosely around the compressor handle. (If so equipped) 9. Store the air compressor in a clean and dry location. D25886 16- ENG TROUBLESHOOTING Performing repairs may expose voltage sources, moving parts or compressed air sources, moving parts or compressed air sources. Personal injury may occur. Prior to attempting any repairs, unplug

Turn the knob clockwise to increase pressure and counterclockwise to decrease pressure. On/Auto/Off Switch Tank Pressure Gauge Outlet Pressure Gauge Regulator Safety Valve Pressure Switch Drain Valve: The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use. Cooling System (not shown): This compressor contains an advanced design cooling system. At the heart of this cooling Drain Valve system is an engineered fan. It is perfectly normal for t

oil leaks will damage carpet, paint or other surfaces in vehicles or trailers. HOW TO PREVENT IT Always place COMPRESSOR on a protective mat when transporting to protect against damage to vehicle from leaks. Remove COMPRESSOR from vehicle immediately upon arrival at your destination. HAZARD WARNING: RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT Unsafe operation of your air compressor Review and understand all instructions could lead to serious injury or death to and warnings in this

Repairs to the cord set or plug MUST be made by a qualified electrician. Extension Cords Using extension cords is not recommended. The use of extension cords will cause voltage to drop resulting in power loss to the motor and overheating. Instead of using an extension cord, increase the working reach of the air hose by attaching another length of hose to its end. Attach additional lengths of hose as needed. If an extension cord must be used, be sure it is: • a 3-wire extension cord that has a 3-

It is normal for electrical contacts within ventilated area free of combustible materials, gasoline, or solvent vapors. If electrical sparks from compressor If spraying flammable materials, locate come into contact with flammable compressor at least 20 feet away from vapors, they may ignite, causing fire or spray area. An additional length of hose explosion. may be required. Store flammable materials in a secure location away from compressor. Never place objects against or on top ventilation ope

Pressure switch "cut-out" too high. unit does not shut off contact a Trained Service Technician. Contact a Trained Service Technician. Air leaks at Tube fittings are not tight Using a soapy water solution fittings. enough. check all exposed fittings for leaks. If needed reseal fittings with pipe sealant tape and retighten securely. Do Not Overtighten. If leaks continue contact a Trained Service Technician. Air leaks in air Defective air tank. Air tank must be replaced. tank or at air Do not repa

When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called “cut-in” pressure. Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off - protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called “

1 7/05 Copyright © 2005 Delta Machinery ESPANOL: PAGINA 25 FRANCAIS: PAGE 49 To learn more about DELTA MACHINERY visit our website at: For Parts, Service, Warranty or other Assistance, please call 1-866-422-4286. SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manu

4. Extension cords comply with specifications. If any of the above conditions cannot be met, or if operation of the compressor repeatedly causes interruption of the power, it may be necessary to operate it from a 20 amp circuit. It is not necessary to change the cord set. A05581 10- ENG OPERATION Know Your Air Compressor READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and

Before Starting Break-in Procedure Serious damage may result if the following break-in instructions are not closely followed. This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced. 1. Make sure the Auto/On/Off switch is in the "OFF" position. 2. Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.) 3.