valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Multiple headphones with one transmitter An additional number of headphones can be used with a single transmitter if they operate on the same frequency. Please consult the appliance’s electrical specification sheets for confirmation on compatibility. Rechargeable system The IR transmitter recharges the headphone’s rechargeable R03/AAA NiMH batteries. First switch off the headphone. Then connect the charging cable between the headphone and the transmitter.The green LED on the headphone will light up during charging. Only use Philips SBC HB550S batteries. 4 XP SBC HC 210.1 SRS 07-04-2003 10:22 Pagina 5 General information Controls Surround sound SRS Headphone The SBC HC 210 allows you to experience an "out-of-the-box" surround sound sensation! The immersive surround sound technology in the SBC HC 210 headphone transforms a stereo signal into a natural, three-dimensional experience – without the need for loudspeakers all around the room. Auto mute for noise free operation reduces the noise disturbance when the sound signal is too low or not available. Neodymium speaker drivers for faster bass response and lower overall distor tion. Kit contents This IR headphone system consists of the following accessories: 1 x SBC HC212 IR transmitter 1 x SBC HC215 IR headphone 1 x SBC CS030/00 12 Volt/200 mA AC/DC adapter (for UK: SBC CS030/05 12 Volt/200 mA AC/DC adapter) 2 x Philips SBC HB550S rechargeable R03/AAA (NiMH) batteries 1 x 3.5 mm plug to 6.3 mm stereo adapter plug 1 recharge cable Transmitter (figure 1) 1 IR transmitting LEDs – transmit audio signal to IR headphone 2 SRS Headphone surround sound button – push the button to switch on the SRS Headphone surround sound (the SRS Headphone logo will light up when activated) 3 Power indication – lights up when in use 4 Power switch – power on/off switch 5 Recharging output – connect the recharge cable to the output 6 DC power – connect to the 12 Volt/ 200 mA AC/DC adapter 7 3.5 mm stereo headphone audio input – connects your IR transmitter to an audio source 8 Headphone (figure 2) IR sensors – to receive IR waves from the transmitter 9 Power indication – lights up when in use 10 Power On/Off – slide the switch to the on or off position to switch the headphone on/off 11 Recharging indicator – lights up when the recharging cable is connected between the headphone and the IR transmitter. Completely empty batteries will be fully charged after about 16 hours 12 Recharging input (figure 3) – switch off the headphone prior to connecting the recharging cable to the transmitter.The recharging indicator on the headphone must light up, indicating that the headphone is being recharged 13 Volume – adjust volume to your desired listening level English 5 XP SBC HC 210.1 SRS 07-04-2003 10:22 Pagina 6 Installation English Transmitter power supply IMPORTANT Use only Philips SBC CS030/00 12 Volt/200 mA AC/DC adapter. (For UK version: SBC CS030/05 12 Volt/200 mA AC/DC adapter) 1 Make sure the adapter’s rated voltage corresponds to the mains socket voltage. 2 Connect the DC connector of the AC/DC adapter to the 12 Volt DC power input connector located at the rear of the transmitter. 3 Connect the 12 Volt/200 mA AC/DC adapter to the mains socket. – Always disconnect the AC/DC adapter if the transmitter is not to be used for a long period of time. Headphone power supply IMPORTANT Only use Philips SBC HB550S batteries (R03/AAA NiMH). 1 Check if the power button of the IR headphone is in the on position. 2 Ensure the batteries are put in the batter y compar tment correctly according to the engraved polarity symbols. 3 To recharge the headphone’s rechargeable R03/AAA NiMH batteries, first switch off the headphone.Then connect the charge cable between the headphone and the transmitter (figure 3).The recharging indicator will light up. Note: Completely empty batteries need approximately 16 hours to recharge. Always remove the batteries if the headphone is not to be used for a long period of time. Batteries contain chemical substances, so they should be disposed of properly. Headphone battery replacement (figure 4) IMPORTANT Only use Philips SBC HB550S batteries (R03/AAA NiMH). 1 Open the headphone’s batter y compar tment. 2 Take out the batteries and dispose of them properly. 3 Inser t new batteries. Only use Philips SBC HB550S batteries. 4 Make sure the batteries are correctly inser ted as indicated by the engraved symbols in the batter y compar tment. 5 Close the batter y compar tment. IMPORTANT Before using the IR headphone for the first time, please ensure that the batteries are fully charged for about 16 hours.This will guarantee a longer operating lifetime of the batteries. 6 XP SBC HC 210.1 SRS 07-04-2003 10:22 Pagina 7 Audio Connections Audio Connections Connecting the IR transmitter to a headphone output of an audio source (figure 5) 1 Connect the 3.5 mm stereo plug of the stereo audio cable to the headphone output of an audio source, such as TV, HiFi or PC. – In case your audio source ...