valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Then, once again try changing the resolution. After the change, be sure to restart the computer. An afterimage appears If an image is displayed for a prolonged period of time, an afterimage may appear. This is not a malfunction. The afterimage will disappear when a different screen is displayed. The motion of the mouse cursor is not smooth Select [Start]-[Settings]-[Control Panel]-[Mouse]-[Motion] and add the check mark y [Show pointer trails]. # Disk Operations Cannot read/write to a floppy disk ® Has the floppy disk been correctly inserted? © Has the floppy disk been correctly formatted? © Has the Setup Utility been used to set [Floppy Operation] to [Enable]? (Q3 ^nuaP Setup Utility") Unable to write to a floppy disk Is the floppy disk write-protected? How to format a floppy disk is unclear Select [Format] in [My Computer] - [3 1/2 Floppy (A:)] - [File]. After confirming the disk volume and format type, start formatting. Unable to read/write to the hard disk О Your drive or file may not have been properly set. ' © Check to see if the hard disk is full. If it is full, delete unnecessary files. © Your hard disk content may be corrupted. Contact Panasonic Technical Support. Trouble has occurred with the CD You may need to clean the lens or CD; refer to (C^page 15) on how to do so. When the previous item is not the cause Try testing another drive or media. The access lamp (@) does not light Is the CD loaded on the tray correctly? Cannot play CD or read data from it Is the CD bent, scratched, or dirty? Cannot eject CD Is the computer powered on? н To remove a CD when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. Pushing it completely to the end will free the tray so that it can be pulled out. Emergency Hole^Nf^ The CD-ROM drive vibrates a lot Is the CD bent or labeled? Reinstalling Software Before Reinstallation Preparing 4WjndôwsÎ9.5l FIRSTAID CD Windows 95 CD-ROM FIRSTAID FD (you made earlier) 4Wjndowsl981 Product Recovery CD-ROM FIRSTAID FD (you made earlier) If you have not created the FIRSTAID FD, you can create by selecting [Create FIRSTAID FD] in [Start]-[Programs]-[Panasonic]. If for some reason, you do not have this disk or it is corrupted, please contact Panasonic Technical Support. _j important Ф Save all important data. If reinstallation is carried out, all data existing prior to the installation will be lost. The reinstallation will return the computer to factory condition. • Be sure to remove all PC Cards and disconnect all peripherals before the re installation procedure. • Be sure the AC adapter is connected until completing reinstallation. Reinstalling ШвЗзтШ Windows 95 (HDD format) If data on your hard disk is compressed, the data should be uncompressed. V ... . y 1 Insert the FIRSTAID FD, and turn the computer on; this screen should appear. Microsoft Windows 95 Startup Menu 1. Boot 2. Initialize the HDD for the Hibernation function 3. Restore the HDD to factory default 2 You can choose to create the hibernation domain. To use the hibernation function, follow this procedure and be sure to create the hibernation domain. (If you decide not create this domain, after restarting the computer, go on to step @.) 0 Select 12.1nitialize the HDD for the Hibernation function). © At the confirmation message, press m ©When the message [Press any key to continue...) is displayed, confirm that the FIRSTAID FD has been set in the floppy drive, and then press a key. The computer will reboot. ©When the message [Press FI for Setup] is displayed, press ( F1 ) and then run the Setup Utility. ©Select [Load Default Settings (PnP)J, then press (Enter 1 At the confirmation message, press (Enter). © In [Power Management), set [Power Switch] to [On-Off] and set [Power Saving] to [OFF], press C Esc 1 ©Set [USB Controller] in [Supervisor Setup] to [Enable], press C Esc ) ® Save the settings and then close the Setup Utility. The computer will reboot, and will then return to the display shown in stepf. ( lWindowsl98B : page 22) Windows 95 (reinstalling) 3 Select (3. Restore the HDD to factory default]. 4 At the confirmation message, press any key. 5 When your computer prompts you to insert the FIRSTAID CD, please set the specified CD and press any key. 6 When your computer prompts you to insert the "Windows 95 CD-ROM", please set the specified CD and press any key. 7 When the [To continue, press Enter...] appears, press C Enter 1 After Microsoft ScanDisk completes, the computer will automatically return to the Windows 95 setup. Simply follow the on-screen instructions . 9 With the exception of the instruction below, please select all default values displayed by the Setup Wizard. Be sure to add the check mark s to [Sound, MIDI, or Video Capture Card] at the [Analyzing Your Computer] . $ Have a floppy disk on hand to create a "Windows 95 Startup Disk". Immediately after creating this disk, enter the...