valutazioni - , GPA: ( )

Istruzioni per l'uso Panasonic, Modello CF73E3KVXDM

Produttore : Panasonic
File Size : 2.02 mb
File Nome : CF73E3KVXDM.PDF

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

May require board repair. *0280 Previous boot incomplete - Default configuration used Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was caused by incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify that the wait-state configuration is correct. This error is cleared the next time the system is booted. 0281 Memory Size found by POST differed from EISA CMOS Memory size found by POST differed from EISA CMOS. 02B0 Diskette drive A error 02B1 Diskette drive B error Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly. 02B2 Incorrect Drive A type - run SETUP Type of floppy drive A: not correctly identified in Setup. 02B3 Incorrect Drive B type - run SETUP Type of floppy drive B: not correctly identified in Setup. 02D0 System cache error - Cache disabled Contact Panasonic Technical Support. 02F0: CPU ID: CPU socket number for Multi-Processor error. 02F4: EISA CMOS not writable ServerBIOS2 test error: Cannot write to EISA CMOS. 21 Troubleshooting Troubleshooting List of Error Codes 02F5: DMA Test Failed ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers. 02F6: Software NM1 Failed ServerB10S2 test error: Cannot generate software NMI (Non-Maskable Interrupt). 02F7: Fail - Safe Timer NMI Failed ServerB10S2 test error: Fail-Safe Timer takes too long. device address Conflict Address conflict for specified device. Allocation Error for: device Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device. Failing Bits : nnnn The hex number nnnn is a map of the bits at the RAM address which failed the memory test. Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of the failure in System, Extended or Shadow memory. Invalid System Configuration Data Problem with NVRAM (CMOS) data. I/O device IRQ conflict I/O device IRQ conflict error. Operating System not found Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed disk and drive A: are properly identified. Parity Check 1 nnnn Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. Parity is a method for checking errors in binary data. A parity error indicates that some data has been corrupted. Parity Check 2 nnnn Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. Press to resume, to Setup Displayed after any recoverable error message. Press to start the boot process or to enter a Setup and change the settings. Write down and follow the information shown on the screen. 22 Dealing with Problems (Summary) When a problem occurs, refer to this page. The “Reference Manual” also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. 9 Starting Up The power indicator or battery indicator is not lit • Check the cable connection for the AC adaptor. • Check to see if a fully charged battery is properly inserted. • Remove the battery pack and disconnect the AC adaptor, then connect them again. [Enter Password! is displayed Input your password. If you have forgotten it, contact Panasonic Technical Support. POST Startup Error(s) is displayed page 21 Windows startup, or an operation is extremely slow Press C F9 ) in the Setup Utility (Q= “Setup Utility”). This will restore the Setup Utility’s settings to their default values (except the password settings). Then, the Setup Utility must be run once again for you to input the appropriate operating environment settings. (The processing speed depends on the application software used, so this operation may not cause the processing speed to increase.) The date and time are incorrect ' • You can set the date and time using the following procedure: [Control Panel] - [Date/Time] [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time] • If you continue to experience problems, the internal battery maintaining the clock may need to be replaced. Contact Panasonic Technical Support. • When the computer is connected to a LAN, confirm the date and time of the server. • This computer will not correctly recognize the date and time starting from the year 2100 A.D. When resuming from the standby or hibernation mode, [Enter Password[ does not appear even if a password has been set in the Setup Utility Ev...