Log:
valutazioni - 0, GPA: 0 ( )

Istruzioni per l'uso Dell, Modello Precision M4300

Produttore : Dell
File Size : 1.35 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


NOTE: A PC Card is not a bootable device. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. The computer recognizes most cards and automatically loads the appropriate device driver. If the configuration program tells you to load the manufacturer's drivers, use the floppy disk or CD that came with the PC Card. ExpressCard 1. Hold the card with its orientation symbol pointing into the slot and the top side of the card facing up. The latch may need to be in the "in" position before you insert the card. 2. Slide the card into the slot until the card is completely seated in its connector. If you encounter too much resistance, do not force the card. Check the card orientation and try again. The computer recognizes most cards and automatically loads the appropriate device driver. If the configuration program tells you to load the manufacturer's drivers, use the floppy disk or CD that came with the card. If you have an adapter, such as the one shown below, you can use 34-mm ExpressCards in the PC Card slot. For information about using the PC Card slot, see PC Card. Removing a Card or Blank Press the latch and remove the card or blank. For some latches, you must press the latch twice: once to pop the latch out, and then a second time to pop the card out. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in your Product Information Guide. NOTICE: Click the icon (in the taskbar) to select a card and stop it from functioning before you remove it from the computer. If you do not stop the card in the configuration utility, you could lose data. Do not attempt to eject a card by pulling its cable, if one is attached. Back to Contents Page Back to Contents Page Coin-Cell Battery Dell™ Precision™ M4300 Service Manual 1. Follow the procedures in Before You Begin. 2. Remove the memory module cover (see Memory). 3. Remove the coin-cell battery connector from the connector on the system board. 4. Slide the battery out of the plastic sleeve. Back to Contents Page CAUTION: Before performing the following procedures, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching a connector on the back panel of the computer. 1 plastic sleeve 2 coin-cell battery 3 coin-cell battery connector 4 connector on system board Back to Contents Page Processor Module Dell™ Precision™ M4300 Service Manual Removing the Processor Module Installing the Processor Module Removing the Processor Module 1. Follow the procedures in Before You Begin. 2. Remove the hinge cover (see Hinge Cover). 3. Remove the keyboard (see Keyboard). 4. Remove the display assembly (see Display Assembly). 5. Remove the palm rest (see Palm Rest). 6. Remove the processor thermal-cooling assembly (see Processor Thermal-Cooling Assembly). 7. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop. The ZIF-socket cam screw secures the processor to the system board. Take note of the arrow on the ZIF-socket cam screw. 8. Use a processor extraction tool to remove the processor module. Installing the Processor Module CAUTION: Before performing the following procedures, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching a connector on the back panel of the computer. NOTICE: Press and hold the processor down by applying slight pressure to the center of the processor while turning the cam screw to prevent intermittent contact between the cam screw and processor. NOTICE: To avoid damage to the processor, hold the screwdriver so that it is perpendicular to the processor when turning the cam screw. NOTICE: When removing the processor module, pull the module straight up. Be careful not to bend the pins on the processor module. 1 ZIF-socket 2 ZIF-socket cam screw 3 pin-1 corner of processor NOTICE: Ensure that the cam lock is in the fully open position before seating the processor module. Seating the processor module properly in the ZIF socket does not require force. 1. Align the pin-1 corner of the processor module so that it points to the triangle on the ZIF socket, and insert the processor module into the ZIF socket. When the processor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the others, the module is not seated correctly. 2. Tighten the ZIF socket by turning the cam screw clockwise to secure the processor module to the system board. 3. Replace the processor thermal-cooling assembly (see Processor Thermal-Cooling Assembly). 4. Update the BIOS using a flash BIOS-update program CD (see Flashing the BIOS From a CD). Back to Contents Page NO...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie