valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Use this switch to select the appropriate voltage according to the voltage supply in your area. If the voltage supply in your area is 100-127V, set the switch to 115V. 115V/230V 115V/230V115V/230V115V/230V115V/230V115V/230V Voltage selector Voltage selectorVoltage selectorVoltage selectorVoltage selectorVoltage selector If the voltage supply in your area is CAUTION. CAUTION.CAUTION.CAUTION.CAUTION.CAUTION. Setting the 200-240V, set the switch to 230V. switch to 115V in a 230V Internal components 11111 22222 1. PFC power supply 4. 2. Motherboard 5. 3. Two 5.25” optical drive bays 6. environment will seriously damage the system! 33333 44444 55555 66666 3.5” HDD drive bay 3.5” Floppy drive bay Hard disk drive bays Removing the side plate and front cover ScrewScrewScrewScrewScrew 11111 Remove the two screws on the rear panel. 22222 33333 IMPORTANT. IMPORTANT.IMPORTANT.IMPORTANT.IMPORTANT.IMPORTANT. Repeat steps 1 and 2 to remove the other side plate. Side lock tab Side lock tabSide lock tabSide lock tabSide lock tabSide lock tab Release the side lock tabs. Hinge-like tabHinge-like tabHinge-like tabHinge-like tabHinge-like tab 44444 Swing the left edge of the front panel outward, then unhook the hinge-like tabs from the holes on the right side of the front panel. Installing a CPU CAUTION. CAUTION.CAUTION.CAUTION.CAUTION.CAUTION. Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU! 90 -100 Socket Lever Socket LeverSocket LeverSocket LeverSocket LeverSocket Lever 11111 Lift up the socket lever to a 90°-100° angle. 22222 Gold triangle Gold triangleGold triangleGold triangleGold triangleGold triangle Small triangle Small triangleSmall triangleSmall triangleSmall triangleSmall triangle Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. Installing system memory DIMM notchDIMM notchDIMM notchDIMM notchDIMM notch 11111 11111 22222 Socket break Socket breakSocket breakSocket breakSocket breakSocket break CAUTION. CAUTION.CAUTION.CAUTION.CAUTION.CAUTION. A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM. Installing the fan and heatsink assembly • The retention module base is already installed on the motherboard upon purchase. You do not have to remove the retention module base when installing the CPU or installing other motherboard components. • If you purchased a separate CPU heatsink and fan assembly, make sure that a Thermal Interface Material is properly applied to the CPU heatsink or CPU before you install the heatsink and fan assembly. Retention bracket lockRetention bracket lockRetention bracket lockRetention bracket lockRetention bracket lock RetentionRetentionRetentionRetentionRetention Module BaseModule BaseModule BaseModule BaseModule Base Retention bracketRetention bracketRetention bracketRetention bracketRetention bracket 11111 22222 Attach one end of the retention bracket to the retention module base. 33333 Align the other end of the retention bracket to the retention module base. A clicking sound denotes that the retention bracket is in place. 44444 Push down the retention bracket lock on the retention mechanism to secure the heatsink and fan to the module base. IMPORTANT. IMPORTANT.IMPORTANT.IMPORTANT.IMPORTANT. IMPORTANT. Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector. Installing an optical drive 1111111111 22222 33333 Remove the drive bay plate. 44444 Red stripe to pin 1Red stripe to pin 1Red stripe to pin 1Red stripe to pin 1Red stripe to pin 1 IDE ribbon cableIDE ribbon cableIDE ribbon cableIDE ribbon cableIDE ribbon cable Audio cableAudio cableAudio cableAudio cableAudio cable Power cable Power cablePower cablePower cablePower cablePower cable Installing a hard disk drive HDD labelHDD labelHDD labelHDD labelHDD label sidesidesidesideside 11111 22222 4444433333 Primary IDE connector Primary IDE connectorPrimary IDE connectorPrimary IDE connectorPrimary IDE connectorPrimary IDE connector IDE ribbon cable IDE ribbon cableIDE ribbon cableIDE ribbon cableIDE ribbon cableIDE ribbon cable Connect the blue interface of the IDE ribbon cable Power cable Power cablePower cablePower cablePower cablePower cable to the primary IDE connector (blue connector labeled PRI_IDE1) on the motherboard. Replacing the side plate and front cover ScrewScrewScrewScrewScrew 43Side lock tabSide lock tabSide lock tabSide lock tabSide lock tab Hinge-like tabHinge-like tabHinge-like tabHinge-like tabHinge-like tab Snap the side lock tabs to secure the front panel. 21 Drive in two screws on the rear panel. IMPORTANT. IMPORTANT.IMPORTANT.IMPORTANT.IMPORTANT.IMPORTANT. Repeat steps 3 and 4 to replace the other side plate. ...