valutazioni - 4, GPA: 4.8
(
)
)
|
Facilità d'uso
Result: The machine should move in the direction that the blue arrow points on the drive chassis, then come to an abrupt stop. 48 Slowly move the drive control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the yellow arrow points on the drive chassis, then come to an abrupt stop. Note: The drive brakes must be able to hold the machine on any slope it is able to climb. PartNo.43650 Genie S-80 & Genie S-85 Operator's Manual Second Edition· Fifth Printing FUNCTION TESTS Test the Drive Enable System 49 Move the lift/drive select switch to the lift position (if equipped). 50 Press down the foot switch. Then lower the boom to the stowed position. Result: The drive enable indicator light should come on and remain on while the boom is anywhere in the range shown. 52 Move the lift/drive select switch to the drive position (if equipped). 53 Move the drive control handle off center. Result: The drive function should not operate. 54 Move and hold the drive enable toggle switch to either side and slowly move the drive control handle off center. Result: The drive function should operate. Note: When the drive enable system is in use, the machine may drive in the opposite direction that the drive and steer control handle is moved. Use the color-coded direction arrows on the platform Blue controls and the drive chassis to identify the direction of travel. Yellow Test Limited Drive Speed 55 Move the lift/drive select switch to the lift position (if equipped). 56 Press down the foot switch. 57 Raise the boom to just above horizontal. 58 Move the lift/drive select switch to the drive position (if equipped). 59 Slowly move the drive control handle to the full drive position. Result: The maximum achievable drive speed with the boom raised should not exceed 1 foot per second (0.3 meters per second). 60 Move the lift/drive select switch to the lift position (if equipped). 61 Lower the boom to the stowed position. 62 Extend the boom 1 foot (30 cm). 63 Move the lift/drive select switch to the drive position (if equipped). 64 Slowly move the drive control handle to the full drive position. Result: The maximum achievable drive speed with the boom extended should not exceed 1 foot per second (0.3 meters per second). If the drive speed with the boom raised or extended exceeds 1 foot per second (0.3 meters per second), immediately tag and remove the machine from service. Genie S-80 & Genie S-85 PartNo.43650 Second Edition · Fifth Printing Operator's Manual Test Auxiliary Controls 65 Shut off the engine. 66 Pull out the red Emergency Stop button to the ON position. 67 Move the lift/drive select switch to the lift position (if equipped). 68 Press down the foot switch. 69 Simultaneously hold auxiliary power switch on and activate each function control handle or toggle switch. Note: To conserve battery power, test each function through a partial cycle. Result: All boom and steer functions should operate. Drive functions should not operate with auxiliary power. FUNCTION TESTS Test the Lift/Drive Select Switch (if equipped) 70 Move the lift/drive select switch to the lift position. 71 Press down the foot switch. 72 Move the drive control handle off center. Result: No drive functions should operate. 73 Activate each boom function toggle switch. Result: All boom functions should operate. 74 Move the lift/drive select switch to the drive position. 75 Press down the foot switch. 76 Activate each boom function toggle switch. Result: No boom functions should operate. 77 Move the drive control handle off center. Result: The drive functions should operate. PartNo.43650 Genie S-80 & Genie S-85 Operator's Manual Second Edition· Fifth Printing Work Place Inspection Do Not Operate Unless: You learn and practice the principles of safe machine operation contained in this operator's manual. 1 Avoid hazardous situations. 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the work place. Know and understand the above principles before going on to the next section. 5 Only use the machine as it was intended. Fundamentals The Work Place Inspection helps the operator determine if the work place is suitable for safe machine operation. It should be performed by the operator prior to moving the machine to the work place. It is the operator's responsibility to read and remember the work place hazards, then watch for and avoid them while moving, setting up and operating the machine. Work Place Inspection Be aware of and avoid the following hazardous situations: · drop-offs or holes · bumps, floor obstructions or debris · overhead obstructions and high voltage conductors · hazardous locations · inadequate surface support to withstand all load forces imposed by the machine · wind and weather conditions · the presence of unauthorized personnel · other possible u...
Questo manuale è adatto anche per i modelli :Attrezzature per TC - S-80 (1.5 mb)
Attrezzature per TC - S-85 (1.5 mb)