valutazioni - 5, GPA: 4.2 ( )

Produttore : Husqvarna File Size : 3.55 mb File Nome : Lingua di insegnamento:

If the vehicle is hard to start in cool or cold temperatures, simply push in the choke cover to activate it. Hold it during start up and release the choke cover after the engine starts and runs smoothly. 12 Figure 13 Choke Figure 14 Low Oil Warning Light and Headlight Switch LOW OIL WARNING LIGHT Gasoline Vehicles Only The gasoline golf car is equipped with a low oil warning light (1), located on the dash panel to the right of the key switch (Figure 14). If the warning light comes on, oil should be checked and added to the engine as necessary before continuing to use the vehicle. The vehicle should never be driven with the low oil warning light remaining on. If the warning light goes on and off, you may proceed, but oil should be added at the first opportunity. If the oil level is correct and the warning light stays on, have a trained technician check the vehicle. See following CAUTION. 2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual Page 19 Pre-Operation and Daily Safety Checklist CAUTION • Failure to add oil immediately when the low oil warning light stays on may result in permanent engine damage. HEADLIGHT CONTROL The headlight control (2) is located on the dash to the left of the key switch (Figure 14). Pull out to turn the lights on, push in to turn the lights off. The headlights operate on 12 volts DC from the battery. See following NOTE. NOTE: Using the headlights for extended periods of time without the engine running, or with the engine idling, will discharge the battery. 12-VOLT OUTLET ACCESSORY Some vehicles are provided with a 12-volt outlet, protected with a 10 amp fuse, located in the fuse box under the seat. To use, push in a cord designed for this type of outlet. Be sure to disconnect electronic devices from the accessory outlet before the vehicle batteries are charged. See following CAUTION. y CAUTION • Do not leave electronic devices connected to the accessory outlet while the vehicle batteries are being charged. The voltage output can fluctuate from 12 volts to 19 volts while the vehicle batteries are charging, and this voltage fluctuation can damage some electronic devices. To remove a power cord from the accessory outlet, rotate it counterclockwise, align the arrows and pull the cord out of the outlet. Extended use of this accessory can cause the batteries to become heavily discharged. If the vehicle batteries become deeply discharged, charge the batteries as instructed in the owner’s manual appropriate to the vehicle, or contact your local Husqvarna dealer for instructions. Inspect the accessory outlet periodically to ensure the electrical connection is clean and free of corrosion. PRE-OPERATION AND DAILY SAFETY CHECKLIST Each Husqvarna vehicle has been thoroughly inspected and adjusted at the factory; however, upon receiving your new vehicle(s), you should become familiar with its controls, indicators, and operation. Carefully inspect each vehicle to ensure that it is in proper working condition before accepting delivery. Use the following checklist as a guide to inspect the vehicle. This checklist should be used daily to ensure that the vehicle is in proper working condition and in conjunction with the Periodic Service Schedules on page 32. Any problems should be corrected by a Husqvarna distributor/dealer or a trained technician. • General: All the parts should be in place and properly installed. Be sure that all nuts, bolts, and screws are tight. On gasoline vehicles check all hose clamps for tight fit as well as the starter belt for tightness. • Safety and information decals: Check to ensure that all safety and information decals are in place. See Safety Decal and Feature Identification on page 4. • Tires: Check for proper tire pressure. Visually inspect tires for wear, damage, and proper inflation on a daily basis. See Vehicle Specifications on page 50. Page 20 2008 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual Performance Inspection • Battery(ies): Check electrolyte to ensure that it is at its proper level (Figure 21, Page 38 or Figure 26, Page 43). Check battery posts. Wires should be tight and free of corrosion. On electric vehicles charge batteries fully before first use of vehicle. • Charger cord, plug, and receptacle (electric vehicles): Visually inspect for cracks, loose connections, and frayed wiring. See Plug and Receptacle on page 41. • Engine (gasoline vehicles): Check for proper engine oil level. See Engine Oil – Gasoline Vehicles on page 44. • Fuel (gasoline vehicles): Check fuel level. See Fueling Instructions – Gasoline Vehicles on page 47. Check fuel tank, lines, cap, pump, fuel filters, and carburetor for fuel leakage. • Exhaust system (gasoline vehicles): Check for leaks. y WARNING • Be sure the plastic has been removed from the seat bottom before operating the vehicle. Failure to do so may result in a fire, property damage, personal injury, or death. PERFORMANCE INSPECTION After you have familiarized yourself with the vehi...

Scarica la tua

Per scaricare, digitare 2 cifre :