valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SPECIFIC SAFETY RULES WARNING: When using outdoor use portable lamps, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONSUse only three-wire outdoor extension cords that have three-prong groundling plugs and grounding receptacles that accept the appliance’s plug. Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the wet location portable lamp. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety. Use only with an extension cord for outdoor use, such as an extension cord of cord type SW, SW-A, SOW, SOW-A, STW, STWOA, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, or SJTOW, SJTOW-A. SAVE THESE INSTRUCTIONSOperation Instructions Press the Switch (16) once to turn the light on and again to turn the light off. To adjust the angle of the Worklight, set the Worklight down and turn the round adjusting knob on the side of the Worklight counter-clockwise. Once loosened, the body of the Worklight can be adjusted to move up or down. Turn the adjusting knob clockwise to the tighten the knob and lock the Worklight body in place. Bulb Replacement Unplug the lamp and allow the bulb to cool completely. Peel back the covers of the four Tap Screws (1) that are located on the top, bottom, right and left sides of the Lamp Cover (2). Using a screwdriver (not included), unscrew the four 3 X 12 Tap Screws (1). Remove the Lamp Cover (2), Sponge Strip (3), Rubber Ring (4) and then the Glass covering (5). Unscrew the Lamp Tube (6) and remove from the body of the Worklight. Replace with a similar 25 watt fluorescent bulb set. Put the Glass covering (5), Rubber Ring (4), Sponge Strip (3) and Lamp Cover (2) back into place. Then place the Lamp Cover (2) back into place and tighten with the four 3 X 12 Tap Screws (1). INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch of the tool is in its “OFF” position, that the tool is unplugged from its electrical outlet, and that the bulb is allowed to cool completely before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. Warranty 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Limited 90 Day warranty PARTS LIST PartDescriptionQ’ty1Tap Screw 3 X 1242Lamp Cover13Sponge Strip14Rubber Ring15Glass16Lamp Tube17Reflector18Tap Screw 3 X 1429Fender210Housing111Tap Screw 3 X 144PartDescriptionQ’ty12PVC Handle113Left and Right Ha...