valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
Remove the tail light assembly from the vehicle by removing the original bulb sockets from the housing. Then remove the housing hardware so it can be removed from the car. Remove the housings from the vehicle carefully so the housing to body gaskets are not damaged. 2. Next remove the lens. The 67-68 Camaro has six screws that hold the housing halves together which will need to be removed to gain access to lens. The 70-73 Camaro lens has tabs locking it into the plastic housing. Pry the tabs gently with a screwdriver to remove lens. 3.Now is a good time toclean the lens and housing. If lenses are in bad shape a new set is recommended. If you are installing this kit into a 67-68Camaro skip aheadto step 5. For the 70-73Camaro, some ofthe hardware will need to be changed outforproper mountingbracket 4.Changing the installed 67-68 mountbrackettothe70-73mounting bracket. a.Note how the current assembly is attached and notice how the wires are routed for re- assembly.ENSURETHEWIRES ARE NOTPINCHED IN THE NEWASSEMBLY. b.Removethe screw at the back of the LEDassembly;it is a5/8” 6-32 machine screw. This will remove themounting bracketthat willneed tobe changed. c.Locate the supplied longer mountbracketand reattach using the shorter supplied 1/2” 6-32 machine screw.The shorter screw must be used since the taller mount is thinner. Tighten the screw down in the center of the slot.The LED assembly can be moved up or down to adjust the heightof the light. d.Note: NOT FOLLOWING THESESTEPSCANDAMAGETHE CIRCUIT BOARD! 1967-1968 Camaro mount1970-1973 Camaro mount 1970-1973 Camaro LEDAssembly 5.Remove the mountingplatefrom the bottomof theassemblywhichis attached with two 3/8” 6- 32 machine screws. 6.Pass the wires through the tail lighthousing where the original bulb and socket were. MAN# 650153 7.Feed the wiresthroughthe larger hole in themountingplate. Guide themounting plateto the bottom of the housing.The flatsideof themountingplateshould bedown and the side with the slight raised center should go upintothe housing. Thiswillalignthe mount in the original housing. 8.Nowhold the LED assemblyso that it iscentered over the hole where the original bulb waslocatedand alignthe mountingplate from the bottom with the slot in the housing.The screwholes should be lined up. 9.Screw the mounting plate into the assemblymountusing the two previously removed 3/8”6-32 screws. 10.Install the lens and/or re-assemble the tail lighthousing, insuring all gaskets are intactand in place. Install thetail lighthousing back into the vehicle.You are now ready to wirethe LEDassembly into the vehicle tail lightharness. 11.Start by cuttingoff the existing light socketas itwill not be used.Do not strip wires. Trim the wires from LED assembly to appropriate length once mounted,making sure wires are routed cleanly and securely. 12.Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LEDassembly to the existing vehicle harness.Insert appropriate wire from vehicle harnessandmating LED assembly wire into a connector and crimp following instructionsbelow. *For the bestconnection,soldering isrecommended.But to simplify installation, thesupplied connectors willprovidea fastweather resistant connection. Thecorrect crimp method for the supplied connectors is: 1.) InsertUNSTRIPPEDwiresfrom both LED assembly and vehicle harnessinto the connectorand ensurethey are all they way in by observing the clearbottom ofthe connector to see thewires are touching the end. 2.) Use pliers to push the blue cap down flush with the edge ofthe clear body,completing theconnection.The connection will only be correct if pressedfirmlydown with pliers. MAN# 650153 GREEN wire from LED assemblyTurn Signal wire from vehicle harnessBROWN wire from LED assemblyTail Light wire from vehicle harnessBLACK wire from LED assemblyGround wire from vehicle harnesswith plastic housingsBLACK wire from LED assemblyAttach to metal bolt or screw for Ground connection with metal housingsOR LED wires Vehicle harness Taillight Brown Brown Driver’s Turn Green Green Passenger’s Turn Green Yellow Ground Black Chassis or body 13. Repeat for the other side. 14. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash you will need to upgrade your flasher. If you are replacing only the rear turn signals you should be able to use a heavy duty electronic flasher from your local parts store. If you are replacing both front and rear or do not have front bulbs you will need a no-load flasher, Dakota Digital part number LAT-NLF. Service and Repair DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems. Should you ever need to send the unit back for repairs, please call our technical support line, ...