valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
INTRODUCTION Thank you for choosing the Black & Decker®V-1 Million Power Series™Spotlight.Please read this guide carefully before use to ensure optimum performance and to avoid damage to the unit. FEATURES • Powerful, focused quartz halogen beam • Protective rubber safety guard (bezel) around lens • Rubber safety cap protects battery compartment • Comfortable pistol grip • Battery Status LED Indicator • UL listed, built-in 120 volt AC charger that works with a standard household extension cord (not included) • 12 volt DC charging adapter included • Rechargeable, non-spillable, sealed lead acid battery RUBBER BEZEL TRIGGER ON/OFF DC CHARGING PORT TRIGGER LOCK BATTERY STATUS LED INDICATOR 120 VOLT AC CHARGER (BACK OF UNIT) QUARTZ HALOGEN BULB PISTOL GRIP HANDLE CHARGING/RECHARGING THE SPOTLIGHT This unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC Charger for 12-14 hours or until the red Battery Status LED flashes. Charge after each use until red LED flashes. Charging/Recharging Using the 120 Volt AC Charger and a Standard Household Extension Cord (not included) Plug a standard North American 120 volt AC extension cord (not included) into the 120 Volt AC Charger on the back of the unit. BATTERY STATUS LED INDICATOR BUILT-IN 120V AC CHARGER Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). 3 SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 4 Charge until the Battery Status LED Indicator red LED flashes (approximately 12-14 hours). DO NOT CHARGE FOR LONGER THAN 14 HOURS. Charging/Recharging Using the 12 Volt DC Charging Adapter Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port. 12 VOLT DC CHARGING PORT 12 VOLT DC CHARGING ADAPTER Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source. Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed). Charge until the Battery Status LED Indicator red LED flashes (approximately 12-14 hours). DO NOT CHARGE FOR LONGER THAN 14 HOURS. Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is 12 volt DC and is able to supply at least one half amp at 12 volt DC for 8 hours. This means a battery pack should be charged with at least 4 amp hours capacity. Note: When using a vehicle’s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the accessory outlet. WARNING: NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY. OPERATING INSTRUCTIONS To turn the Spotlight ON, depress the Trigger. To lock the Trigger in the ON position, depress the Trigger, then slide TRIGGER the Trigger Lock up. The spotlight will stay on until the lock is moved to the OFF position and the trigger is released. TRIGGER LOCK CARE AND MAINTENANCE All batteries lose charge with time, especially when they are warm. Recharge the unit every two months when not in frequent use, preferably using the 120 volt AC method. Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent. The quartz halogen bulb is the only user-replaceable part in the Spotlight. Periodically inspect the condition of adapters, connectors and wires. Contact Technical Support toll-free at 1-800-544-6986 to replace any components that have become worn or broken. Spotlight Bulb Replacement To replace the bulb, you will need a small Phillips screwdriver and a 6 volt H3 55 watt replacement bulb. During installation, avoid touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be wiped clean with a cloth moistened with alcohol. RETAINING RING RUBBER “O” RING REFLECTOR RUBBER END CAP TRIGGER LOCK TRIGGER SWITCH QUARTZ HALOGEN BULB RUBBER BEZEL COVER 4 SL102B_ManualEN_051007.qxp 5/10/07 9:13 AM Page 5 1. Disconnect the unit from any charging adapters. 2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in the retaining ring. 3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside. 4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside. 5. Carefully remove the reflector and bulb assembly. BULB REFLECTOR HAIRPIN RET AINING WIRES PHILLIPS HEAD SCREWS 6. Disconnect the bulb wire from the red power wire. 7. Unsnap the hairpin retaining wires from the reflector’s flange. 8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this screw). 9. Lift out the bulb and detach wire. 10. Insert the replacement bulb into the reflector’s flange. 11. Put back and secure the hairpin retaining wires. 12. Connect the bulb power wire to the red...
Questo manuale è adatto anche per i modelli :Illuminazione - Power Series V-1 Million (346.16 kb)