valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Green LED LED. After 30 minutes, reinsert battery pack in on indicates battery pack is fully charged and charger. If green LED continues to remain on, return charger is in trickle charge mode. Note: Green battery pack to your nearest Sears Repair Center for LED will remain on until battery pack is removed checking or replacing. from charger or charger is disconnected from Note: This situation only occurs when continuous use power supply. of your worklight causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal re- BATTERYPACK charging of batteries. If the charger does not charge SHOWNIN CHARGER your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check. CHARGER REDLEDON INDICATES GREENLEDON AFTERFASTCHARGING CYCLE,INDICATESFULLYCHARGEDBATTERY PACKANDINTRICKLECHARGEMODE. YELLOWANDGREENLEDSONINDICATESDEEPLY DISCHARGEDOR DEFECTIVEBATTERYPACK. Fig. 1 4 LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK: • Red LED on = Fast charging mode. • Green LED on = Fully charged and in trickle charge mode. • Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack isout of or below normal temperature range, • Yellow and Green LEDs on = Deeply discharged or defective battery pack, • No LED on = Defective charger or battery pack, _ CAUTION: To prevent damage to battery pack, remove battery pack from charger immediately if no LED comes on. Return battery pack and charger to your nearest Sears Service Center for checking or replacing. Also, if you are removing battery pack from charger and no LEDs are on, return both battery pack and charger to your nearest Sears Service Center. Do not insert another battery pack into charger. A damaged charger may damage a battery pack. TO INSTALL/REMOVE BATTERY PACK See Figure 2. • Use only the recommended battery pack withyour worklight. _, WARNING: Do not install battery pack to your worklight until you have read and understood all precautions and operating instructions in the manual and printed on battery pack and charger. • Orient battery pack so that raised rib on battery pack aligns with groove inside worklight. Battery pack is designed to fit only one way in worklight handle. • Insert battery pack, making sure latches on each side of battery pack snap into place and battery pack is secure in worklight before use. CAUTION: When placing battery pack in your worklight, be sure raised rib on battery pack aligns with groove inside worklight handle and latches snap into place properly. Improper assembly of battery pack can cause damage to internal components. • To remove battery pack, locate latches on end of battery pack and depress to release battery pack from your worklight. SWITCH See Figure 3. To turn your worklight on and off, depress switch trigger. MULTI-POSITION HEAD See Figure 3. Your worklight has the feature of a multi-position head that has positive stop clicks at each position. Rotate head to the desired position as shown in the arrows in Figure 3. MULTI-POSITION SWITCH TRIGGER BATTERY PACK LATCHES Fig. 3 LATCHESTO RELEASEBATTERYPACK Fig. 2 5 _1= WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. _, WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. BULB REPLACEMENT See Figure 4. When purchasing replacement bulb, request recom mended part number 7811502. See Figure 4. TO REPLACE BULB: • Remove battery pack from worklight. See Page ,5. • Depress button located on top of len cover then pull lens cover to remove. • Remove old bulb from spring by twisting bulb in a clockwise direction. LENSCOVER DEPRESS PULLLENS BUTTON COVERFORWARD TO REMOVE Do not abuse power tools. Abusive practices can damage tool as well as workpiece, ,_ WARNING: Do not attempt to modify this worklight or create accessories not recommended for use with this worklight. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. • Insert new bulb in spring by twisting bulb in a clockwise direction. • Replace lens cover aligning tabs inside lens cover with slots on housing then snap into place. • Replace battery pack. Note: For your convenience, your worklight has a bulb storage area to store an extra bulb. See Figure 4. BUTTON BULB STORAGEAREA SLOT FORMODELNO.973.110470 REQUESTBULBPARTNO.7811502 Fig. 4 BATTERIES Your worklight's battery pack is equipped with nickel- cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this worklight have been designed to provide maximum trouble free ...
Questo manuale è adatto anche per i modelli :Illuminazione - 973.110470 (722.42 kb)