Log:
valutazioni - 2, GPA: 4.5 ( )

Istruzioni per l'uso Elation Professional, Modello PAR56

Produttore : Elation Professional
File Size : 516.6 kb
File Nome : eled_tri_par56.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to the shipper. ©Elation Lighting® - - ELED TRI PAR56 Instruction Manual Page 3 ©Elation Lighting® - - ELED TRI PAR56 Instruction Manual Page 4 DMX512 IN3-PIN XLRSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTDMX512DMX+,DMX-,COMMON123Termination reduces signal transmission interference. connect a DMX Ohm 1/4 W) and PIN 3 (DMX 123123DMX + DMX - COMMONDMX512 OUT3-PIN XLR ELED TRI PAR56 Set Up ELED TRI PAR56 Set Up Power Supply: The Elation ELED TRI PAR56 contains an electronic ballast, which will auto sense the voltage when it is plugged into the power source. With the electronic ballast you do not need to worry about wall voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX Operation): The ELED TRI PAR56 can be controlled via DMX-512 protocol. The ELED TRI PAR56 has 6 DMX modes, please see pages 10-12 for the different modes. The DMX address is set on the back panel of the ELED TRI PAR56. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split. Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX512 IN3-PIN XLRSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTSOUNDREMOTECONTROLINPUTPOWERINPUTOUTPUTDMX512DMX+,DMX-,COMMON123Termination reduces signal errors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. 123123DMX + DMX - COMMONDMX512 OUT3-PIN XLR Figure 2 XLR Female Socket XLR Male Socket XLR Pin Configuration 1 Ground 2 Cold 2 Cold 1 Ground Pin 1 = Ground Pin 2 = Data Compliment (negative) 3 Hot 3 Hot Pin 3 = Data True (positive) Figure 3 Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. Figure 4 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- 512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion 5-Pin X...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie